Activity Stream - Let's Talk ShopBot

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

01-26-2023, 09:55 AM

phil_o replied to a thread Did I just waste $700? in VCarvePro and PhotoVCarve

I have a Shopbot PRT, with a 4g Board, circa 2006. Works great. This is the PP I use. I have Aspire but that should make any difference. Phil

14 replies | 3906 view(s)

01-24-2023, 08:05 PM

Mike Windsor started a thread indexer post processor in Troubleshooting

I'm trying to figure out what's going on with my indexer . first time using it . I created a rounding toolpath in aspire V11.5 and have the indexer...

0 replies | 54 view(s)

01-21-2023, 04:20 PM

srwtlc replied to a thread Odd noise in ShopBotter Message Board

Good catch Russ! Yes, if the font wasn't created in VCP, but brought in from another program as a dxf etc., you can get many nodes that then create...

6 replies | 251 view(s)

01-21-2023, 11:18 AM

chiloquinruss replied to a thread Odd noise in ShopBotter Message Board

Another area to look at is the actual toolpath created by that font. If you select the vector in node mode the font curves should be just a few...

6 replies | 251 view(s)

01-20-2023, 12:00 PM

Slant replied to a thread For Sale: 2015 PRS Alpha ATC 4'x8'x8" +Vac Table + Single Phase 5HP Spindle - Nice! in For Sale/Wanted - ShopBot-related items only

Dropping price again! Motivated to sell! Asking $19,950! I can help with shipping and installation. Give me a call or text anytime! Josh 530...

2 replies | 1097 view(s)

01-19-2023, 11:10 AM

Mike Caul replied to a thread Squaring a 2014 desktop gantry in ShopBot Desktop

Thanks Scott, I've searched that myself and have never seen it either. I never really discovered the issue, until I did a 2 sided project. Mike

2 replies | 156 view(s)

01-19-2023, 12:08 AM

matt_raymond60 replied to a thread Odd noise in ShopBotter Message Board

I will give that a try. Thank you!

6 replies | 251 view(s)

01-19-2023, 12:07 AM

matt_raymond60 replied to a thread Odd noise in ShopBotter Message Board

Good to know! Sounds horrible but is cutting nicely. Happy to have in action again. Thank you!!

6 replies | 251 view(s)

01-18-2023, 03:12 PM

waynelocke replied to a thread Odd noise in ShopBotter Message Board

PRTs made a horrible growling sound when the x and y axis were going simultaneously. It sounds like something must be wrong but relax. All is as it...

6 replies | 251 view(s)

01-18-2023, 02:07 PM

srwtlc replied to a thread Odd noise in ShopBotter Message Board

If your cuts look good, it could just be that you are using a feedrate that falls in a bad "motor resonance" range. Try some different feedrates to...

6 replies | 251 view(s)

01-18-2023, 01:20 PM

dlcw replied to a thread Did I just waste $700? in VCarvePro and PhotoVCarve

Aspire and VCarve Pro, directly from Vectric, work fine on my 2009 PRSAlpha.

14 replies | 3906 view(s)

01-18-2023, 10:11 AM

reveal1123 replied to a thread For Sale: Shopbot Buddy BT32 w/ 14" Z & Dewalt Router - $6,000 in For Sale/Wanted - ShopBot-related items only

This has been sold. Thank you for the space.

7 replies | 837 view(s)