PDA

View Full Version : Archives2005



  1. Grounding
  2. Losing steps?
  3. X Motor
  4. Proximity switch repeatability?
  5. Need help with my inconsistant "z" depths
  6. Porter Cable HEAT
  7. Bending ABS Plastic
  8. Should there be play in the Vexta steppers?
  9. Probe "disconnect" problem
  10. Blown Driver??? (again)
  11. European Import
  12. Comm Break at -0 -1
  13. 220V electrical connection to the control box...Need Help!
  14. Setiing up new shopbot...Router won't power up...Help?
  15. Shopbot prt Alpha Problems
  16. Bit deflection-how much is to be expected
  17. Colombo Spindle Noise
  18. SHOPBOT NOT CONNECTING
  19. Help with stop button
  20. Recovering lost files
  21. Acrylic Edge Quality
  22. PRTAlpha Control Box Heat
  23. Prob Problem
  24. Proximity Switches, Sb stops BUT software runs on
  25. PR model Z axis bearings
  26. ERROR "53"
  27. Finally up and running but..................PC wont turn off
  28. Problems with the jogging and moving speeds
  29. Circle Cutting Problem
  30. PR Upgraded to PRT -- No Communication with controller
  31. VU (value units) problem
  32. Where to start
  33. Intermittently losing the controller ...
  34. Clunky Curves
  35. Vectors from illustrator 10
  36. Table Surfacing problems
  37. Control board intallation problem
  38. PC ROUTER BEARING REPLACEMENT
  39. Columbo bearing replacement?
  40. SHOP BOT LOSING POSITION
  41. Help for a rookie
  42. Need a hand in South Florida
  43. LOST KEY COMMANDS IN DOS CUT SOFTWEAR
  44. X motors reversing direction at random
  45. Shopbot Software 2.32
  46. Suppress warning messages (VA,ZT,ST)
  47. Outputs on circa 99 PR?
  48. FG command question
  49. Zero Plate
  50. Limit Switch lights up but carraige doesn't stop
  51. Driver/Motor Fault Location
  52. X motor makes grinding noise-doesn't move
  53. Question about possible VA file conversion
  54. Problem with Alpha software????
  55. Poor cut quality in plex
  56. What will run on WinXP?
  57. Losing Control Box Connection
  58. Is there somebodi with BERGES inverter
  59. 1proximity switch not turning off
  60. Dialing in my table
  61. Bits burning up
  62. Trouble with a PR model
  63. Heat Issues
  64. A different kind of HEAT issue
  65. Limit swich hit
  66. Timer Over-run
  67. Software and port issues.
  68. Router won't turn on new Alpha upgrade
  69. Newbie Qu;ery - Banging carriage setting Z
  70. Connection Help
  71. Router issues
  72. Inconsistent widths and backlash (long)
  73. Z won't plunge into surface
  74. 5 HP Colombo
  75. Motor tightners
  76. Cut Issue
  77. Artcampro7
  78. Question about E-Stop / Remote Stop on Alpha
  79. Types of mistakes, cut failures. Looking before we leap
  80. Calibration Issues
  81. Inconsistent z travel
  82. Problem with move speed settings
  83. Cutting differently
  84. A huge bummer.....
  85. StairStepped Z-moves
  86. PRT - jog issues
  87. Computer freezes up
  88. Blown Z Driver?
  89. Serial Port Failure - Reboot
  90. X axis moving in Wrong Direction
  91. Colombo Collets Breaking
  92. HELP SHOPBOT DRIVING INTO TABLE
  93. Blown Driver Board...I think
  94. No Actual Movement
  95. Expansive MDF
  96. Other routers that I can mount in my shopbot?
  97. Error 11 "Division by zero"
  98. Lines wont connect
  99. Scaling problem
  100. Indexer
  101. LOSING CONNECTION WHEN SPINDLE COMES ON
  102. It runs 5,6,7,8,9 cycles, then it doesn't!
  103. Troubleshooting a vacuum leak?
  104. SB Control Version 3.4.15 problem
  105. Ok, I'm a dummy - how do I...
  106. Can't run setup routine -first time, other concerns
  107. How do you set spindle speed with the Delta VFD
  108. Reset table size, squaring Z again, surfacing table
  109. Cutting differently
  110. Error message
  111. Probe indicator light not lighting
  112. Blown fuse
  113. Reset drivers???
  114. Copy machine question.