Page 1 of 38 12311 ... LastLast
Threads 1 to 20 of 744

Forum: Techniques for Cutting, Drilling, Machining

Sub-Forums Threads / Posts  Last Post

  1. Forum Actions:

    Forum Statistics:

    • Threads: 735
    • Posts: 7,052

    Last Post:

    Best tool for trimming /... Go to last post

    by curtiss

    06-16-2015, 08:43 PM

  1. Shopbot pauses before drilling hole

    Started by Zads, 08-14-2020 03:05 PM
    • Replies: 3
    • Views: 336
    08-15-2020, 10:47 AM Go to last post
  2. ShopBot Circles cuts out of alignment

    Started by CDarby67, 07-20-2020 08:17 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 1,117
    07-21-2020, 11:50 AM Go to last post
  3. V-carve - ridges left after cut

    Started by chein, 05-19-2020 01:04 PM
    • Replies: 4
    • Views: 714
    05-20-2020, 08:45 PM Go to last post
  4. Question Cut Parameter Recommendations

    Started by BasisPet, 04-05-2020 08:38 AM
    • Replies: 8
    • Views: 1,082
    04-06-2020, 11:43 AM Go to last post
  5. Part Larger then VCarve file

    Started by Rcornelson, 03-23-2020 01:04 PM
    • Replies: 2
    • Views: 489
    03-23-2020, 04:56 PM Go to last post
  6. Bit choice for a project

    Started by CDarby67, 02-28-2020 04:25 PM
    • Replies: 2
    • Views: 690
    02-29-2020, 05:04 PM Go to last post
  7. Using PVA as a mask

    Started by coryatjohn, 01-05-2020 08:43 PM
    • Replies: 4
    • Views: 1,122
    02-21-2020, 08:22 AM Go to last post
  8. Precise cutting of heavy brass tube

    Started by coryatjohn, 12-11-2019 12:56 PM
    • Replies: 4
    • Views: 989
    12-13-2019, 02:59 PM Go to last post
  9. Liquid Urethane Foam

    Started by coryatjohn, 11-26-2019 03:58 PM
    • Replies: 6
    • Views: 1,141
    11-28-2019, 11:05 AM Go to last post
    • Replies: 8
    • Views: 1,231
    11-19-2019, 11:38 PM Go to last post
  10. question on deep cutting

    Started by ddrumguy, 10-20-2019 08:34 AM
    • Replies: 4
    • Views: 1,203
    10-24-2019, 12:29 AM Go to last post
    • Replies: 7
    • Views: 1,556
    10-01-2019, 08:59 PM Go to last post
  11. 30° V-bit woes

    Started by blackhawk, 10-01-2019 01:48 PM
    • Replies: 0
    • Views: 542
    10-01-2019, 01:48 PM Go to last post
  12. Aluminum Feeds & Speeds

    Started by Hobodog2, 08-18-2019 12:49 PM
    • Replies: 0
    • Views: 975
    08-18-2019, 12:49 PM Go to last post
  13. Adding a 3.5watts Laser to my Shopbot Desktop

    Started by Marc F. Lupien, 07-28-2019 10:35 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 2,557
    08-03-2019, 10:31 AM Go to last post
  14. 2 lb EPS Foam Carving- Bits, Feeds, Speeds?

    Started by SarahRay, 07-31-2019 07:44 PM
    • Replies: 4
    • Views: 1,301
    08-02-2019, 08:52 AM Go to last post
  15. Slow pocket on small holes with ramps

    Started by WWBeds, 07-17-2019 10:09 AM
    • Replies: 8
    • Views: 1,821
    07-17-2019, 10:17 PM Go to last post
    • Replies: 0
    • Views: 1,577
    07-08-2019, 01:20 PM Go to last post
  16. drilling operation questions...

    Started by yurtkuran, 04-01-2019 10:32 AM
    drill, drilling, fusion360
    • Replies: 9
    • Views: 3,412
    04-02-2019, 04:49 PM Go to last post
  17. How to connect/control laser add-on

    Started by kaaboom_99, 03-27-2019 01:11 AM
    • Replies: 8
    • Views: 2,264
    03-28-2019, 05:48 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •