Page 1 of 36 12311 ... LastLast
Threads 1 to 20 of 707

Forum: Techniques for Cutting, Drilling, Machining

Sub-Forums Threads / Posts  Last Post

  1. Forum Actions:

    Forum Statistics:

    • Threads: 735
    • Posts: 7,052

    Last Post:

    Best tool for trimming /... Go to last post

    by curtiss

    06-16-2015, 08:43 PM

  1. Favorite insert spoilboard / slab surfacer?

    Started by SarahRay, 06-17-2018 03:55 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 713
    08-19-2018, 03:03 PM Go to last post
  2. Cutting 22 guage zinc?

    Started by wespor, 08-01-2018 09:58 PM
    • Replies: 1
    • Views: 254
    08-02-2018, 09:41 AM Go to last post
  3. How deep with a 3/8" compression?

    Started by ClayM325, 07-23-2018 03:52 PM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 800
    07-27-2018, 03:54 PM Go to last post
    • Replies: 3
    • Views: 200
    07-19-2018, 09:17 PM Go to last post
  4. V Carving Cedar Help

    Started by stevenblake, 07-07-2018 05:32 PM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 1,222
    07-15-2018, 08:58 AM Go to last post
  5. moulding toolpath help

    Started by bobmoore, 07-13-2018 01:47 PM
    • Replies: 0
    • Views: 99
    07-13-2018, 01:47 PM Go to last post
  6. Cutting Micarta and G10

    Started by zebratruck, 06-18-2018 03:45 PM
    • Replies: 1
    • Views: 318
    06-18-2018, 06:01 PM Go to last post
  7. Plunge Burns?

    Started by SarahRay, 06-11-2018 08:50 PM
    • Replies: 9
    • Views: 510
    06-14-2018, 04:13 PM Go to last post
  8. Sea Dek

    Started by ccwerks, 06-13-2018 02:02 PM
    • Replies: 4
    • Views: 288
    06-14-2018, 07:52 AM Go to last post
  9. Baltic Birch Blowout- suggestions?

    Started by SarahRay, 05-30-2018 01:25 AM
    • Replies: 7
    • Views: 516
    06-11-2018, 08:26 AM Go to last post
  10. Laser Cutting

    Started by nalaser, 05-30-2018 05:37 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 1,021
    06-08-2018, 12:18 PM Go to last post
  11. 3D MOLD - Advice on Cutting

    Started by Zach Williams, 05-30-2018 10:00 AM
    2 Pages
    1 2
    1/8" end mill, mold making, wood carving
    • Replies: 10
    • Views: 673
    06-01-2018, 02:23 PM Go to last post
  12. Poor Surface at LOW Chipload as well as Perhaps Deflection?

    Started by verhoevc, 05-10-2018 10:46 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 1,033
    05-17-2018, 09:35 PM Go to last post
  13. HDPE bit help 1/8 or 1/2?

    Started by DarinB, 04-25-2018 03:19 PM
    • Replies: 6
    • Views: 672
    05-07-2018, 09:40 PM Go to last post
  14. Need suggestions for pocketing aluminium

    Started by asaraca, 04-23-2018 08:23 PM
    • Replies: 7
    • Views: 488
    04-24-2018, 10:53 AM Go to last post
  15. Rubber cutting advice

    Started by kfitz, 04-23-2018 09:08 PM
    • Replies: 0
    • Views: 166
    04-23-2018, 09:08 PM Go to last post
  16. Miter Fold bit selection/recommendations

    Started by jTr, 02-07-2018 11:48 AM
    • Replies: 2
    • Views: 756
    04-04-2018, 08:54 PM Go to last post
  17. v-inlay technique problems

    Started by bking1836, 03-15-2018 09:34 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 1,637
    03-19-2018, 09:08 PM Go to last post
  18. Tool Marking

    Started by Archtech, 03-05-2018 11:16 PM
    • Replies: 1
    • Views: 454
    03-06-2018, 12:39 AM Go to last post
  19. hardwood profile cutout advice -- my first paying commission!

    Started by bking1836, 02-10-2018 10:25 AM
    3 Pages
    1 2 3
    • Replies: 28
    • Views: 2,735
    02-15-2018, 11:49 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •