Page 1 of 38 12311 ... LastLast
Threads 1 to 20 of 742

Forum: Techniques for Cutting, Drilling, Machining

Sub-Forums Threads / Posts  Last Post

  1. Forum Actions:

    Forum Statistics:

    • Threads: 735
    • Posts: 7,052

    Last Post:

    Best tool for trimming /... Go to last post

    by curtiss

    06-16-2015, 08:43 PM

  1. V-carve - ridges left after cut

    Started by chein, 05-19-2020 01:04 PM
    • Replies: 4
    • Views: 236
    05-20-2020, 08:45 PM Go to last post
  2. Question Cut Parameter Recommendations

    Started by BasisPet, 04-05-2020 08:38 AM
    • Replies: 8
    • Views: 690
    04-06-2020, 11:43 AM Go to last post
  3. Part Larger then VCarve file

    Started by Rcornelson, 03-23-2020 01:04 PM
    • Replies: 2
    • Views: 320
    03-23-2020, 04:56 PM Go to last post
  4. Bit choice for a project

    Started by CDarby67, 02-28-2020 04:25 PM
    • Replies: 2
    • Views: 506
    02-29-2020, 05:04 PM Go to last post
  5. Using PVA as a mask

    Started by coryatjohn, 01-05-2020 08:43 PM
    • Replies: 4
    • Views: 866
    02-21-2020, 08:22 AM Go to last post
  6. Precise cutting of heavy brass tube

    Started by coryatjohn, 12-11-2019 12:56 PM
    • Replies: 4
    • Views: 742
    12-13-2019, 02:59 PM Go to last post
  7. Liquid Urethane Foam

    Started by coryatjohn, 11-26-2019 03:58 PM
    • Replies: 6
    • Views: 883
    11-28-2019, 11:05 AM Go to last post
    • Replies: 8
    • Views: 942
    11-19-2019, 11:38 PM Go to last post
  8. question on deep cutting

    Started by ddrumguy, 10-20-2019 08:34 AM
    • Replies: 4
    • Views: 963
    10-24-2019, 12:29 AM Go to last post
    • Replies: 7
    • Views: 1,201
    10-01-2019, 08:59 PM Go to last post
  9. 30° V-bit woes

    Started by blackhawk, 10-01-2019 01:48 PM
    • Replies: 0
    • Views: 409
    10-01-2019, 01:48 PM Go to last post
  10. Aluminum Feeds & Speeds

    Started by Hobodog2, 08-18-2019 12:49 PM
    • Replies: 0
    • Views: 800
    08-18-2019, 12:49 PM Go to last post
  11. Adding a 3.5watts Laser to my Shopbot Desktop

    Started by Marc F. Lupien, 07-28-2019 10:35 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 2,057
    08-03-2019, 10:31 AM Go to last post
  12. 2 lb EPS Foam Carving- Bits, Feeds, Speeds?

    Started by SarahRay, 07-31-2019 07:44 PM
    • Replies: 4
    • Views: 1,006
    08-02-2019, 08:52 AM Go to last post
  13. Slow pocket on small holes with ramps

    Started by WWBeds, 07-17-2019 10:09 AM
    • Replies: 8
    • Views: 1,459
    07-17-2019, 10:17 PM Go to last post
    • Replies: 0
    • Views: 1,383
    07-08-2019, 01:20 PM Go to last post
  14. drilling operation questions...

    Started by yurtkuran, 04-01-2019 10:32 AM
    drill, drilling, fusion360
    • Replies: 9
    • Views: 2,927
    04-02-2019, 04:49 PM Go to last post
  15. How to connect/control laser add-on

    Started by kaaboom_99, 03-27-2019 01:11 AM
    • Replies: 8
    • Views: 1,893
    03-28-2019, 05:48 PM Go to last post
    • Replies: 5
    • Views: 1,807
    02-20-2019, 11:06 AM Go to last post
  16. Am I over-complicating 2-sided machining?

    Started by Torri31, 02-04-2019 01:02 PM
    • Replies: 0
    • Views: 667
    02-04-2019, 01:02 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •