Page 1 of 38 12311 ... LastLast
Threads 1 to 20 of 742

Forum: Techniques for Cutting, Drilling, Machining

Sub-Forums Threads / Posts  Last Post

  1. Forum Actions:

    Forum Statistics:

    • Threads: 735
    • Posts: 7,052

    Last Post:

    Best tool for trimming /... Go to last post

    by curtiss

    06-16-2015, 08:43 PM

  1. V-carve - ridges left after cut

    Started by chein, 05-19-2020 01:04 PM
    • Replies: 4
    • Views: 434
    05-20-2020, 08:45 PM Go to last post
  2. Question Cut Parameter Recommendations

    Started by BasisPet, 04-05-2020 08:38 AM
    • Replies: 8
    • Views: 797
    04-06-2020, 11:43 AM Go to last post
  3. Part Larger then VCarve file

    Started by Rcornelson, 03-23-2020 01:04 PM
    • Replies: 2
    • Views: 367
    03-23-2020, 04:56 PM Go to last post
  4. Bit choice for a project

    Started by CDarby67, 02-28-2020 04:25 PM
    • Replies: 2
    • Views: 561
    02-29-2020, 05:04 PM Go to last post
  5. Using PVA as a mask

    Started by coryatjohn, 01-05-2020 08:43 PM
    • Replies: 4
    • Views: 924
    02-21-2020, 08:22 AM Go to last post
  6. Precise cutting of heavy brass tube

    Started by coryatjohn, 12-11-2019 12:56 PM
    • Replies: 4
    • Views: 802
    12-13-2019, 02:59 PM Go to last post
  7. Liquid Urethane Foam

    Started by coryatjohn, 11-26-2019 03:58 PM
    • Replies: 6
    • Views: 948
    11-28-2019, 11:05 AM Go to last post
    • Replies: 8
    • Views: 1,017
    11-19-2019, 11:38 PM Go to last post
  8. question on deep cutting

    Started by ddrumguy, 10-20-2019 08:34 AM
    • Replies: 4
    • Views: 1,028
    10-24-2019, 12:29 AM Go to last post
    • Replies: 7
    • Views: 1,292
    10-01-2019, 08:59 PM Go to last post
  9. 30° V-bit woes

    Started by blackhawk, 10-01-2019 01:48 PM
    • Replies: 0
    • Views: 439
    10-01-2019, 01:48 PM Go to last post
  10. Aluminum Feeds & Speeds

    Started by Hobodog2, 08-18-2019 12:49 PM
    • Replies: 0
    • Views: 842
    08-18-2019, 12:49 PM Go to last post
  11. Adding a 3.5watts Laser to my Shopbot Desktop

    Started by Marc F. Lupien, 07-28-2019 10:35 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 2,195
    08-03-2019, 10:31 AM Go to last post
  12. 2 lb EPS Foam Carving- Bits, Feeds, Speeds?

    Started by SarahRay, 07-31-2019 07:44 PM
    • Replies: 4
    • Views: 1,079
    08-02-2019, 08:52 AM Go to last post
  13. Slow pocket on small holes with ramps

    Started by WWBeds, 07-17-2019 10:09 AM
    • Replies: 8
    • Views: 1,574
    07-17-2019, 10:17 PM Go to last post
    • Replies: 0
    • Views: 1,432
    07-08-2019, 01:20 PM Go to last post
  14. drilling operation questions...

    Started by yurtkuran, 04-01-2019 10:32 AM
    drill, drilling, fusion360
    • Replies: 9
    • Views: 3,080
    04-02-2019, 04:49 PM Go to last post
  15. How to connect/control laser add-on

    Started by kaaboom_99, 03-27-2019 01:11 AM
    • Replies: 8
    • Views: 1,999
    03-28-2019, 05:48 PM Go to last post
    • Replies: 5
    • Views: 1,907
    02-20-2019, 11:06 AM Go to last post
  16. Am I over-complicating 2-sided machining?

    Started by Torri31, 02-04-2019 01:02 PM
    • Replies: 0
    • Views: 709
    02-04-2019, 01:02 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •