Page 1 of 35 12311 ... LastLast
Threads 1 to 20 of 695

Forum: Techniques for Cutting, Drilling, Machining

Sub-Forums Threads / Posts  Last Post

  1. Forum Actions:

    Forum Statistics:

    • Threads: 735
    • Posts: 7,052

    Last Post:

    Best tool for trimming /... Go to last post

    by curtiss

    06-16-2015, 08:43 PM

  1. Poor Surface at LOW Chipload as well as Perhaps Deflection?

    Started by verhoevc, 05-10-2018 10:46 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 680
    05-17-2018, 09:35 PM Go to last post
  2. HDPE bit help 1/8 or 1/2?

    Started by DarinB, 04-25-2018 03:19 PM
    • Replies: 6
    • Views: 489
    05-07-2018, 09:40 PM Go to last post
  3. Need suggestions for pocketing aluminium

    Started by asaraca, 04-23-2018 08:23 PM
    • Replies: 7
    • Views: 330
    04-24-2018, 10:53 AM Go to last post
  4. Rubber cutting advice

    Started by kfitz, 04-23-2018 09:08 PM
    • Replies: 0
    • Views: 90
    04-23-2018, 09:08 PM Go to last post
  5. Miter Fold bit selection/recommendations

    Started by jTr, 02-07-2018 12:48 PM
    • Replies: 2
    • Views: 650
    04-04-2018, 08:54 PM Go to last post
  6. v-inlay technique problems

    Started by bking1836, 03-15-2018 09:34 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 1,345
    03-19-2018, 09:08 PM Go to last post
  7. Tool Marking

    Started by Archtech, 03-06-2018 12:16 AM
    • Replies: 1
    • Views: 369
    03-06-2018, 01:39 AM Go to last post
  8. hardwood profile cutout advice -- my first paying commission!

    Started by bking1836, 02-10-2018 11:25 AM
    3 Pages
    1 2 3
    • Replies: 28
    • Views: 2,181
    02-16-2018, 12:49 AM Go to last post
  9. Need suggestions on carving blue foam

    Started by asaraca, 01-12-2018 11:03 AM
    • Replies: 5
    • Views: 752
    02-08-2018, 10:56 AM Go to last post
  10. Two sided machining hold down

    Started by JoshBot, 02-03-2018 12:59 PM
    • Replies: 2
    • Views: 446
    02-03-2018, 05:57 PM Go to last post
  11. Corian

    Started by Paramedia, 01-10-2018 09:49 AM
    • Replies: 8
    • Views: 1,038
    01-27-2018, 09:40 AM Go to last post
    • Replies: 9
    • Views: 672
    01-22-2018, 01:01 PM Go to last post
  12. New toy, could not resist

    Started by Burkhardt, 12-27-2017 05:05 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 1,172
    01-19-2018, 09:52 AM Go to last post
  13. New Line in MSGBOX

    Started by shasselberg, 01-07-2018 01:39 PM
    • Replies: 2
    • Views: 348
    01-07-2018, 07:04 PM Go to last post
  14. Two-Sided Job, Bleeder and Spoil Board

    Started by shasselberg, 12-31-2017 09:39 AM
    2 Pages
    1 2
    bleeder, two-sided, vcarve
    • Replies: 10
    • Views: 1,021
    01-04-2018, 03:25 PM Go to last post
  15. Question Vcarve small objects / distorted

    Started by Lonnie, 12-21-2017 11:52 PM
    • Replies: 4
    • Views: 590
    12-22-2017, 03:40 PM Go to last post
    • Replies: 4
    • Views: 675
    12-07-2017, 11:33 AM Go to last post
  16. Drilling in end of acrylic tube

    Started by Paramedia, 12-07-2017 06:30 AM
    • Replies: 0
    • Views: 285
    12-07-2017, 06:30 AM Go to last post
  17. Cast Acrylic v. Extruded Acrylic

    Started by robtown, 12-05-2017 04:30 PM
    • Replies: 0
    • Views: 285
    12-05-2017, 04:30 PM Go to last post
  18. Random Tool Paths

    Started by ger.wat, 11-20-2017 07:40 PM
    efficient, random, tool paths
    • Replies: 1
    • Views: 426
    11-20-2017, 07:51 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •