Page 3 of 16 FirstFirst 1234513 ... LastLast
Threads 41 to 60 of 304

Forum: ShopBot Buddy

For questions and comments specifically about the Buddy (moving table BT32 and BT48)and the PowerStick.

Sub-Forums Threads / Posts  Last Post

  1. Archives2008

    Forum Actions:

    Forum Statistics:

    • Threads: 34
    • Posts: 287

    Last Post:

    How rigid is the Buddy 48? Go to last post

    by Brady Watson

    12-24-2008, 04:47 PM

  1. How to properly square the Z axis on a Buddy

    Started by asaraca, 09-29-2017 09:24 PM
    2 Attachment(s)
    • Replies: 1
    • Views: 5,067
    Brady Watson
    09-29-2017, 10:55 PM Go to last post

  2. proximity setup to a new zero

    Started by jhedlund58, 09-01-2017 03:04 PM
    • Replies: 6
    • Views: 4,612
    jhedlund58
    09-04-2017, 04:52 PM Go to last post

  3. Older Buddy Questions

    Started by Thomas Cook, 09-02-2017 04:44 PM
    • Replies: 3
    • Views: 3,310
    Brady Watson
    09-02-2017, 08:07 PM Go to last post

  4. stepper motor

    Started by cowboy1296, 08-23-2017 05:21 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 3,199
    Brady Watson
    08-24-2017, 08:28 AM Go to last post

  5. Power Stick upgrade

    Started by jhedlund58, 07-09-2017 10:31 AM
    2 Attachment(s)
    • Replies: 3
    • Views: 3,359
    jhedlund58
    08-20-2017, 08:58 AM Go to last post

  6. Spindle Speed Control Issues

    Started by Carlson, 08-11-2017 04:01 AM
    2 Attachment(s)
    • Replies: 4
    • Views: 3,440
    Carlson
    08-15-2017, 03:22 AM Go to last post

  7. z axis upgrade

    Started by tlempicke, 07-03-2017 10:10 AM
    • Replies: 4
    • Views: 4,868
    tlempicke
    08-06-2017, 01:36 PM Go to last post

  8. Deck table for Buddy 48

    Started by asaraca, 07-10-2017 02:00 PM
    • Replies: 3
    • Views: 3,540
    tlempicke
    07-10-2017, 06:10 PM Go to last post

  9. Power Stick

    Started by tomahack, 06-29-2017 08:55 PM
    • Replies: 1
    • Views: 2,248
    Simops
    06-30-2017, 02:06 AM Go to last post

  10. coat of arms

    Started by cowboy1296, 06-10-2017 10:29 PM
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 11
    • Views: 7,218
    cowboy1296
    06-11-2017, 05:39 PM Go to last post

  11. Any ideas to move a Buddy?

    Started by DarinB, 06-10-2017 03:25 PM
    • Replies: 2
    • Views: 2,569
    DarinB
    06-10-2017, 11:30 PM Go to last post

  12. cleaned and lubed up, and new pinions day

    Started by Ajcoholic, 12-06-2016 09:51 PM
    3 Pages •
    1 2 3
    • Replies: 21
    • Views: 14,406
    cowboy1296
    06-03-2017, 08:42 AM Go to last post

  13. Fuse or Relay?

    Started by angelosart, 05-14-2017 04:08 PM
    • Replies: 3
    • Views: 8,301
    angelosart
    05-18-2017, 09:14 PM Go to last post

  14. Can a ATC go on Buddy Alpha?

    Started by Adam Buchwald, 04-08-2017 04:19 PM
    • Replies: 2
    • Views: 2,993
    Adam Buchwald
    04-09-2017, 09:46 AM Go to last post

  15. Profile 1/8" Off?

    Started by angelosart, 03-02-2017 10:08 PM
    3 Attachment(s)
    • Replies: 3
    • Views: 2,826
    angelosart
    03-03-2017, 04:22 PM Go to last post

  16. Exclamation Buddy Surface Board Off

    Started by angelosart, 02-19-2017 03:30 PM
    1 Attachment(s)
    • Replies: 1
    • Views: 5,365
    cowboy1296
    02-19-2017, 06:43 PM Go to last post

  17. BT32 Alpha not cutting correct dimensions

    Started by DarinB, 06-22-2016 08:44 PM
    1 Attachment(s)
    • Replies: 8
    • Views: 6,904
    DarinB
    11-26-2016, 02:39 PM Go to last post

  18. Consistent Ridges

    Started by angelosart, 08-04-2016 08:42 AM
    1 Attachment(s)
    • Replies: 0
    • Views: 6,849
    angelosart
    08-04-2016, 08:42 AM Go to last post

  19. What do you Recommend a laptop to run shobot/Aspire software ?

    Started by drfaux, 06-18-2016 12:04 PM
    • Replies: 5
    • Views: 8,292
    srwtlc
    06-18-2016, 07:58 PM Go to last post

  20. Table becomes un connected during carve

    Started by cwfreitas, 06-05-2016 10:43 AM
    • Replies: 1
    • Views: 14,606
    Joe Porter
    06-05-2016, 11:08 AM Go to last post
Page 3 of 16 FirstFirst 1234513 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules