Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 307

Forum: Variations & Modifications of ShopBots

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. how to wire 4 lamb amatek 240v motors

    Started by Stuart Kent, 11-19-2020 10:22 AM
    • Replies: 0
    • Views: 112
    11-19-2020, 10:22 AM Go to last post
  2. Looking for a Post Processor for vacuum pods.

    Started by andrius.ack, 11-11-2020 04:10 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 525
    11-14-2020, 12:48 PM Go to last post
    • Replies: 14
    • Views: 5,030
    11-11-2020, 04:04 PM Go to last post
  3. Increase Power on Yaskawa 2.2hp VFD for Cheap

    Started by PaulWall, 10-31-2020 09:45 PM
    • Replies: 0
    • Views: 245
    10-31-2020, 09:45 PM Go to last post
    • Replies: 0
    • Views: 469
    09-14-2020, 05:18 PM Go to last post
  4. New spindle, control question

    Started by mercuru049, 08-11-2020 03:44 PM
    • Replies: 1
    • Views: 411
    08-11-2020, 06:21 PM Go to last post
  5. FabMo & Raspberry Pi on a V4g control board

    Started by Jimmy Walker, 04-07-2020 02:17 PM
    • Replies: 1
    • Views: 1,174
    04-07-2020, 03:06 PM Go to last post
  6. Anyone installed a spindle at an angle?

    Started by chris_booth, 02-12-2020 07:38 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 2,440
    02-14-2020, 01:09 PM Go to last post
  7. Aftermarket Relay For Extra Output Controls

    Started by NicholasB, 04-23-2018 01:22 PM
    • Replies: 1
    • Views: 3,115
    09-12-2019, 06:11 PM Go to last post
  8. 3D printed dust shoe

    Started by EricSchimel, 08-28-2019 11:18 AM
    • Replies: 2
    • Views: 1,278
    08-28-2019, 12:59 PM Go to last post
  9. Welding my X gantry (Part 1 of 3)

    Started by Chuck Keysor, 06-26-2019 03:58 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 2,880
    06-29-2019, 01:46 AM Go to last post
    • Replies: 3
    • Views: 1,948
    05-11-2019, 06:35 PM Go to last post
  10. New Spindle

    Started by srwtlc, 05-06-2019 07:38 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 3,888
    05-08-2019, 11:38 PM Go to last post
  11. Adding z axis proximity switch to older PRT

    Started by Neonguy65, 04-17-2019 11:14 PM
    • Replies: 1
    • Views: 1,344
    04-18-2019, 07:52 AM Go to last post
  12. Shopbot PRT upgrades

    Started by Neonguy65, 03-21-2019 03:33 PM
    • Replies: 0
    • Views: 1,276
    03-21-2019, 03:33 PM Go to last post
  13. Proximity switch replacement

    Started by kamen, 11-25-2018 04:00 PM
    • Replies: 4
    • Views: 3,128
    02-06-2019, 10:30 AM Go to last post
  14. ShopBot Desktop/Handibot drives?

    Started by EricSchimel, 10-30-2018 05:56 PM
    • Replies: 9
    • Views: 3,791
    10-31-2018, 11:41 PM Go to last post
  15. new linear bearing gantry

    Started by Robert Prerovsky, 10-19-2018 04:41 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 4,283
    10-21-2018, 04:34 PM Go to last post
  16. Getting more Z height

    Started by phil_o, 06-16-2018 12:54 PM
    • Replies: 1
    • Views: 2,221
    06-16-2018, 02:49 PM Go to last post
  17. I needed a little more headroom

    Started by a.werby, 02-21-2018 06:32 PM
    • Replies: 2
    • Views: 3,197
    02-22-2018, 05:33 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •