Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 304

Forum: Variations & Modifications of ShopBots

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

    • Replies: 0
    • Views: 116
    09-14-2020, 04:18 PM Go to last post
  1. New spindle, control question

    Started by mercuru049, 08-11-2020 02:44 PM
    • Replies: 1
    • Views: 279
    08-11-2020, 05:21 PM Go to last post
  2. FabMo & Raspberry Pi on a V4g control board

    Started by Jimmy Walker, 04-07-2020 01:17 PM
    • Replies: 1
    • Views: 1,029
    04-07-2020, 02:06 PM Go to last post
  3. Anyone installed a spindle at an angle?

    Started by chris_booth, 02-12-2020 06:38 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 2,107
    02-14-2020, 12:09 PM Go to last post
  4. Aftermarket Relay For Extra Output Controls

    Started by NicholasB, 04-23-2018 12:22 PM
    • Replies: 1
    • Views: 2,933
    09-12-2019, 05:11 PM Go to last post
  5. 3D printed dust shoe

    Started by EricSchimel, 08-28-2019 10:18 AM
    • Replies: 2
    • Views: 1,137
    08-28-2019, 11:59 AM Go to last post
  6. Welding my X gantry (Part 1 of 3)

    Started by Chuck Keysor, 06-26-2019 02:58 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 2,610
    06-29-2019, 12:46 AM Go to last post
    • Replies: 3
    • Views: 1,784
    05-11-2019, 05:35 PM Go to last post
  7. New Spindle

    Started by srwtlc, 05-06-2019 06:38 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 3,506
    05-08-2019, 10:38 PM Go to last post
  8. Adding z axis proximity switch to older PRT

    Started by Neonguy65, 04-17-2019 10:14 PM
    • Replies: 1
    • Views: 1,226
    04-18-2019, 06:52 AM Go to last post
  9. Shopbot PRT upgrades

    Started by Neonguy65, 03-21-2019 02:33 PM
    • Replies: 0
    • Views: 1,170
    03-21-2019, 02:33 PM Go to last post
  10. Proximity switch replacement

    Started by kamen, 11-25-2018 03:00 PM
    • Replies: 4
    • Views: 2,941
    02-06-2019, 09:30 AM Go to last post
  11. ShopBot Desktop/Handibot drives?

    Started by EricSchimel, 10-30-2018 04:56 PM
    • Replies: 9
    • Views: 3,543
    10-31-2018, 10:41 PM Go to last post
  12. new linear bearing gantry

    Started by Robert Prerovsky, 10-19-2018 03:41 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 3,951
    10-21-2018, 03:34 PM Go to last post
    • Replies: 13
    • Views: 4,601
    08-12-2018, 05:48 PM Go to last post
  13. Getting more Z height

    Started by phil_o, 06-16-2018 11:54 AM
    • Replies: 1
    • Views: 2,104
    06-16-2018, 01:49 PM Go to last post
  14. I needed a little more headroom

    Started by a.werby, 02-21-2018 05:32 PM
    • Replies: 2
    • Views: 3,043
    02-22-2018, 04:33 PM Go to last post
  15. Fein Turbo 3

    Started by joe_manor, 10-18-2017 10:02 AM
    • Replies: 5
    • Views: 4,246
    10-30-2017, 06:04 PM Go to last post
  16. storing all the bits and pieces

    Started by Alan m, 10-08-2017 07:27 PM
    • Replies: 9
    • Views: 4,112
    10-18-2017, 10:49 AM Go to last post
  17. My Jtech Laser / Shopbot Journey....So Far

    Started by CStevens, 03-31-2017 01:20 PM
    • Replies: 6
    • Views: 5,470
    05-16-2017, 11:56 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •