Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 302

Forum: Variations & Modifications of ShopBots

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. FabMo & Raspberry Pi on a V4g control board

    Started by Jimmy Walker, 04-07-2020 01:17 PM
    • Replies: 1
    • Views: 889
    04-07-2020, 02:06 PM Go to last post
  2. Anyone installed a spindle at an angle?

    Started by chris_booth, 02-12-2020 06:38 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 1,900
    02-14-2020, 12:09 PM Go to last post
  3. Aftermarket Relay For Extra Output Controls

    Started by NicholasB, 04-23-2018 12:22 PM
    • Replies: 1
    • Views: 2,800
    09-12-2019, 05:11 PM Go to last post
  4. 3D printed dust shoe

    Started by EricSchimel, 08-28-2019 10:18 AM
    • Replies: 2
    • Views: 1,049
    08-28-2019, 11:59 AM Go to last post
  5. Welding my X gantry (Part 1 of 3)

    Started by Chuck Keysor, 06-26-2019 02:58 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 2,398
    06-29-2019, 12:46 AM Go to last post
    • Replies: 3
    • Views: 1,663
    05-11-2019, 05:35 PM Go to last post
  6. New Spindle

    Started by srwtlc, 05-06-2019 06:38 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 3,286
    05-08-2019, 10:38 PM Go to last post
  7. Adding z axis proximity switch to older PRT

    Started by Neonguy65, 04-17-2019 10:14 PM
    • Replies: 1
    • Views: 1,156
    04-18-2019, 06:52 AM Go to last post
  8. Shopbot PRT upgrades

    Started by Neonguy65, 03-21-2019 02:33 PM
    • Replies: 0
    • Views: 1,092
    03-21-2019, 02:33 PM Go to last post
  9. Proximity switch replacement

    Started by kamen, 11-25-2018 03:00 PM
    • Replies: 4
    • Views: 2,814
    02-06-2019, 09:30 AM Go to last post
  10. ShopBot Desktop/Handibot drives?

    Started by EricSchimel, 10-30-2018 04:56 PM
    • Replies: 9
    • Views: 3,414
    10-31-2018, 10:41 PM Go to last post
  11. new linear bearing gantry

    Started by Robert Prerovsky, 10-19-2018 03:41 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 3,765
    10-21-2018, 03:34 PM Go to last post
    • Replies: 13
    • Views: 4,375
    08-12-2018, 05:48 PM Go to last post
  12. Getting more Z height

    Started by phil_o, 06-16-2018 11:54 AM
    • Replies: 1
    • Views: 2,012
    06-16-2018, 01:49 PM Go to last post
  13. I needed a little more headroom

    Started by a.werby, 02-21-2018 05:32 PM
    • Replies: 2
    • Views: 2,954
    02-22-2018, 04:33 PM Go to last post
  14. Fein Turbo 3

    Started by joe_manor, 10-18-2017 10:02 AM
    • Replies: 5
    • Views: 4,092
    10-30-2017, 06:04 PM Go to last post
  15. storing all the bits and pieces

    Started by Alan m, 10-08-2017 07:27 PM
    • Replies: 9
    • Views: 3,981
    10-18-2017, 10:49 AM Go to last post
  16. My Jtech Laser / Shopbot Journey....So Far

    Started by CStevens, 03-31-2017 01:20 PM
    • Replies: 6
    • Views: 5,364
    05-16-2017, 11:56 PM Go to last post
    • Replies: 6
    • Views: 5,714
    03-30-2017, 08:04 PM Go to last post
  17. NPN or PNP Sensor?

    Started by vinnygalbo, 03-23-2017 07:26 PM
    • Replies: 1
    • Views: 2,302
    03-23-2017, 09:22 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •