Page 1 of 15 12311 ... LastLast
Threads 1 to 20 of 299

Forum: Variations & Modifications of ShopBots

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. Welding my X gantry (Part 1 of 3)

    Started by Chuck Keysor, 06-26-2019 02:58 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 515
    06-29-2019, 12:46 AM Go to last post
    • Replies: 3
    • Views: 616
    05-11-2019, 05:35 PM Go to last post
  2. New Spindle

    Started by srwtlc, 05-06-2019 06:38 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 934
    05-08-2019, 10:38 PM Go to last post
  3. Adding z axis proximity switch to older PRT

    Started by Neonguy65, 04-17-2019 10:14 PM
    • Replies: 1
    • Views: 361
    04-18-2019, 06:52 AM Go to last post
  4. Shopbot PRT upgrades

    Started by Neonguy65, 03-21-2019 02:33 PM
    • Replies: 0
    • Views: 362
    03-21-2019, 02:33 PM Go to last post
  5. Proximity switch replacement

    Started by kamen, 11-25-2018 03:00 PM
    • Replies: 4
    • Views: 1,780
    02-06-2019, 09:30 AM Go to last post
  6. ShopBot Desktop/Handibot drives?

    Started by EricSchimel, 10-30-2018 04:56 PM
    • Replies: 9
    • Views: 2,001
    10-31-2018, 10:41 PM Go to last post
  7. new linear bearing gantry

    Started by Robert Prerovsky, 10-19-2018 03:41 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 2,111
    10-21-2018, 03:34 PM Go to last post
    • Replies: 13
    • Views: 2,800
    08-12-2018, 05:48 PM Go to last post
  8. Getting more Z height

    Started by phil_o, 06-16-2018 11:54 AM
    • Replies: 1
    • Views: 1,275
    06-16-2018, 01:49 PM Go to last post
  9. Aftermarket Relay For Extra Output Controls

    Started by NicholasB, 04-23-2018 12:22 PM
    • Replies: 0
    • Views: 1,092
    04-23-2018, 12:22 PM Go to last post
  10. I needed a little more headroom

    Started by a.werby, 02-21-2018 05:32 PM
    • Replies: 2
    • Views: 2,134
    02-22-2018, 04:33 PM Go to last post
  11. Fein Turbo 3

    Started by joe_manor, 10-18-2017 10:02 AM
    • Replies: 5
    • Views: 2,784
    10-30-2017, 06:04 PM Go to last post
  12. storing all the bits and pieces

    Started by Alan m, 10-08-2017 07:27 PM
    • Replies: 9
    • Views: 2,804
    10-18-2017, 10:49 AM Go to last post
  13. My Jtech Laser / Shopbot Journey....So Far

    Started by CStevens, 03-31-2017 01:20 PM
    • Replies: 6
    • Views: 4,173
    05-16-2017, 11:56 PM Go to last post
    • Replies: 6
    • Views: 4,623
    03-30-2017, 08:04 PM Go to last post
  14. NPN or PNP Sensor?

    Started by vinnygalbo, 03-23-2017 07:26 PM
    • Replies: 1
    • Views: 1,608
    03-23-2017, 09:22 PM Go to last post
  15. Using my asm911aadc2.65v servo motor to make timing belt pulleys

    Started by jon, 08-04-2016 01:01 AM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 9,377
    03-22-2017, 02:56 AM Go to last post
    • Replies: 5
    • Views: 2,482
    03-18-2017, 06:58 PM Go to last post
  16. increasing resolution

    Started by jon, 02-04-2017 02:20 PM
    • Replies: 9
    • Views: 3,405
    02-06-2017, 05:04 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •