Page 2 of 16 FirstFirst 123412 ... LastLast
Threads 21 to 40 of 313

Forum: Variations & Modifications of ShopBots

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. Shopbot PRT upgrades

    Started by Neonguy65, 03-21-2019 03:33 PM
    • Replies: 0
    • Views: 8,137
    Neonguy65
    03-21-2019, 03:33 PM Go to last post

  2. Proximity switch replacement

    Started by kamen, 11-25-2018 04:00 PM
    • Replies: 4
    • Views: 12,679
    kamen
    02-06-2019, 10:30 AM Go to last post

  3. ShopBot Desktop/Handibot drives?

    Started by EricSchimel, 10-30-2018 05:56 PM
    • Replies: 9
    • Views: 11,134
    Gary Campbell
    10-31-2018, 11:41 PM Go to last post

  4. new linear bearing gantry

    Started by Robert Prerovsky, 10-19-2018 04:41 PM
    2 Pages •
    1 2
    • Replies: 12
    • Views: 14,410
    Brady Watson
    10-21-2018, 04:34 PM Go to last post

  5. Getting more Z height

    Started by phil_o, 06-16-2018 12:54 PM
    5 Attachment(s)
    • Replies: 1
    • Views: 8,244
    Brady Watson
    06-16-2018, 02:49 PM Go to last post

  6. I needed a little more headroom

    Started by a.werby, 02-21-2018 06:32 PM
    buddy, extrusion, modification, z height 2 Attachment(s)
    • Replies: 2
    • Views: 10,534
    a.werby
    02-22-2018, 05:33 PM Go to last post

  7. Fein Turbo 3

    Started by joe_manor, 10-18-2017 11:02 AM
    • Replies: 5
    • Views: 20,715
    knight_toolworks
    10-30-2017, 07:04 PM Go to last post

  8. storing all the bits and pieces

    Started by Alan m, 10-08-2017 08:27 PM
    2 Attachment(s)
    • Replies: 9
    • Views: 10,910
    Martin Reid
    10-18-2017, 11:49 AM Go to last post

  9. My Jtech Laser / Shopbot Journey....So Far

    Started by CStevens, 03-31-2017 02:20 PM
    7 Attachment(s)
    • Replies: 6
    • Views: 11,760
    jon
    05-17-2017, 12:56 AM Go to last post

  10. XBOX360 Controller Utilizing MACH3 Control Software On Shopbot PRT

    Started by HelicopterJohn, 12-27-2015 02:51 PM
    1 Attachment(s)
    • Replies: 6
    • Views: 10,541
    HelicopterJohn
    03-30-2017, 09:04 PM Go to last post

  11. NPN or PNP Sensor?

    Started by vinnygalbo, 03-23-2017 08:26 PM
    • Replies: 1
    • Views: 6,358
    Gary Campbell
    03-23-2017, 10:22 PM Go to last post

  12. Using my asm911aadc2.65v servo motor to make timing belt pulleys

    Started by jon, 08-04-2016 02:01 AM
    3 Pages •
    1 2 3
    8 Attachment(s)
    • Replies: 21
    • Views: 28,303
    jon
    03-22-2017, 03:56 AM Go to last post

  13. got my 1500.00 chunk of steel from shopbot.

    Started by knight_toolworks, 03-14-2017 01:01 AM
    1 Attachment(s)
    • Replies: 5
    • Views: 8,770
    knight_toolworks
    03-18-2017, 07:58 PM Go to last post

  14. increasing resolution

    Started by jon, 02-04-2017 03:20 PM
    5 Attachment(s)
    • Replies: 9
    • Views: 7,917
    jon
    02-06-2017, 06:04 PM Go to last post

  15. how to support your dc hose

    Started by Alan m, 01-17-2017 08:45 PM
    2 Pages •
    1 2
    4 Attachment(s)
    • Replies: 14
    • Views: 9,683
    Cosmos275
    01-21-2017, 08:27 PM Go to last post

  16. table idea

    Started by Alan m, 01-17-2017 08:32 PM
    5 Attachment(s)
    • Replies: 4
    • Views: 4,429
    Alan m
    01-18-2017, 05:31 PM Go to last post

  17. Increased Black box HG

    Started by marcrunner, 12-03-2016 01:34 AM
    • Replies: 0
    • Views: 2,877
    marcrunner
    12-03-2016, 01:34 AM Go to last post

  18. How much voltage can/should the 4G board get? How about resistance tolerance?

    Started by Mayo, 10-21-2016 11:08 PM
    • Replies: 2
    • Views: 4,299
    bob_dodd
    10-25-2016, 08:25 PM Go to last post

  19. PRT Y-Rails

    Started by JMCS, 10-13-2016 10:17 PM
    • Replies: 1
    • Views: 4,540
    Gary Campbell
    10-20-2016, 11:10 AM Go to last post

  20. Changing from PK 299 to PK 296 motors

    Started by Tom Bachman, 09-30-2016 05:21 PM
    • Replies: 0
    • Views: 2,682
    Tom Bachman
    09-30-2016, 05:21 PM Go to last post
Page 2 of 16 FirstFirst 123412 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules