Page 1 of 34 12311 ... LastLast
Threads 1 to 20 of 672

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. X, Y zeros not always the same?

    Started by ClayM325, 06-13-2018 12:32 PM
    • Replies: 5
    • Views: 294
    06-14-2018, 11:26 PM Go to last post
  2. Shopbot never cut flat

    Started by ClayM325, 06-06-2018 10:04 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 860
    06-11-2018, 09:38 PM Go to last post
    • Replies: 1
    • Views: 136
    06-11-2018, 10:46 AM Go to last post
    • Replies: 2
    • Views: 452
    05-10-2018, 12:51 AM Go to last post
  3. YZ Car Lower Wheel Bearings

    Started by sevans, 04-19-2018 07:05 PM
    • Replies: 2
    • Views: 354
    04-19-2018, 08:36 PM Go to last post
  4. Gusset T Nut Broken

    Started by sevans, 04-17-2018 05:24 PM
    • Replies: 1
    • Views: 253
    04-17-2018, 06:03 PM Go to last post
  5. Z Adjustment Question

    Started by sevans, 04-12-2018 11:00 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 1,555
    04-17-2018, 09:22 AM Go to last post
  6. Unhappy Z jogs too high after update

    Started by ger.wat, 04-02-2018 02:14 PM
    top limit, travel, z axis
    • Replies: 7
    • Views: 682
    04-15-2018, 03:04 PM Go to last post
  7. Z-Zero plate wire came out

    Started by tri4sale, 04-01-2018 10:43 PM
    • Replies: 4
    • Views: 419
    04-03-2018, 01:00 PM Go to last post
  8. Offsets while running, but jogs home correctly

    Started by harryball, 02-21-2018 10:44 AM
    • Replies: 6
    • Views: 859
    02-23-2018, 11:21 AM Go to last post
  9. Communication Error

    Started by stevenblake, 02-18-2018 01:08 PM
    comm error, communication problem, prs, troubleshooting, usb
    • Replies: 8
    • Views: 894
    02-21-2018, 12:42 PM Go to last post
  10. Spindle turning off during cut

    Started by bking1836, 01-18-2018 02:59 PM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 2,633
    01-31-2018, 10:36 PM Go to last post
  11. Resister for Gecko drive G203V

    Started by cwfreitas, 01-27-2018 05:04 PM
    • Replies: 5
    • Views: 488
    01-28-2018, 10:45 PM Go to last post
  12. Z Zero question

    Started by terryjones, 12-31-2017 03:38 PM
    • Replies: 2
    • Views: 558
    12-31-2017, 05:11 PM Go to last post
  13. cutter veering off circle

    Started by bob_reda, 12-27-2017 08:40 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 985
    12-30-2017, 11:58 AM Go to last post
    • Replies: 3
    • Views: 390
    12-29-2017, 02:40 PM Go to last post
  14. Bit PCL583659 1/16" Ball V Carve

    Started by Wilboy64, 12-06-2017 09:09 AM
    • Replies: 9
    • Views: 996
    12-09-2017, 07:58 PM Go to last post
  15. V90 bit not making clean cuts

    Started by DavidZ, 12-04-2017 08:11 PM
    • Replies: 2
    • Views: 487
    12-05-2017, 10:41 AM Go to last post
  16. Z axis command all by it's own!

    Started by letterman7, 10-16-2017 11:13 AM
    • Replies: 4
    • Views: 888
    10-18-2017, 07:30 AM Go to last post
  17. Driver Alarm

    Started by mrsoliver, 10-13-2017 03:17 PM
    prt alpha driver alarm
    • Replies: 1
    • Views: 351
    10-13-2017, 04:16 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •