Page 1 of 34 12311 ... LastLast
Threads 1 to 20 of 679

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. static causing communication problems...again

    Started by bking1836, 10-17-2018 01:30 PM
    3 Pages
    1 2 3
    • Replies: 27
    • Views: 552
    10-18-2018, 12:44 PM Go to last post
    • Replies: 9
    • Views: 518
    10-10-2018, 08:24 AM Go to last post
  2. Oh noes....

    Started by robtown, 09-25-2018 12:28 PM
    • Replies: 9
    • Views: 726
    10-06-2018, 01:11 PM Go to last post
  3. Question problems with arcs

    Started by a_custom_build, 07-15-2018 10:38 PM
    2 Pages
    1 2
    arc, circle, problem, test
    • Replies: 11
    • Views: 1,222
    07-31-2018, 08:14 AM Go to last post
  4. Shopbot never cut flat

    Started by ClayM325, 06-06-2018 10:04 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 1,648
    07-19-2018, 12:41 AM Go to last post
  5. USB transmission times

    Started by NicholasB, 06-27-2018 07:20 PM
    • Replies: 9
    • Views: 617
    07-18-2018, 03:05 PM Go to last post
  6. X, Y zeros not always the same?

    Started by ClayM325, 06-13-2018 12:32 PM
    • Replies: 7
    • Views: 654
    07-17-2018, 09:45 PM Go to last post
  7. shopbot

    Started by hknisely, 07-07-2018 03:43 PM
    • Replies: 4
    • Views: 426
    07-12-2018, 08:14 AM Go to last post
  8. Stepmotor issue...maybe..? Help!

    Started by Djed, 06-30-2018 07:40 PM
    • Replies: 2
    • Views: 301
    07-01-2018, 10:47 AM Go to last post
    • Replies: 1
    • Views: 282
    06-11-2018, 10:46 AM Go to last post
    • Replies: 2
    • Views: 599
    05-10-2018, 12:51 AM Go to last post
  9. YZ Car Lower Wheel Bearings

    Started by sevans, 04-19-2018 07:05 PM
    • Replies: 2
    • Views: 500
    04-19-2018, 08:36 PM Go to last post
  10. Gusset T Nut Broken

    Started by sevans, 04-17-2018 05:24 PM
    • Replies: 1
    • Views: 405
    04-17-2018, 06:03 PM Go to last post
  11. Z Adjustment Question

    Started by sevans, 04-12-2018 11:00 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 2,296
    04-17-2018, 09:22 AM Go to last post
  12. Unhappy Z jogs too high after update

    Started by ger.wat, 04-02-2018 02:14 PM
    top limit, travel, z axis
    • Replies: 7
    • Views: 910
    04-15-2018, 03:04 PM Go to last post
  13. Z-Zero plate wire came out

    Started by tri4sale, 04-01-2018 10:43 PM
    • Replies: 4
    • Views: 614
    04-03-2018, 01:00 PM Go to last post
  14. Offsets while running, but jogs home correctly

    Started by harryball, 02-21-2018 10:44 AM
    • Replies: 6
    • Views: 1,032
    02-23-2018, 11:21 AM Go to last post
  15. Communication Error

    Started by stevenblake, 02-18-2018 01:08 PM
    comm error, communication problem, prs, troubleshooting, usb
    • Replies: 8
    • Views: 1,148
    02-21-2018, 12:42 PM Go to last post
  16. Spindle turning off during cut

    Started by bking1836, 01-18-2018 02:59 PM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 3,326
    01-31-2018, 10:36 PM Go to last post
  17. Resister for Gecko drive G203V

    Started by cwfreitas, 01-27-2018 05:04 PM
    • Replies: 5
    • Views: 686
    01-28-2018, 10:45 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •