Page 1 of 35 12311 ... LastLast
Threads 1 to 20 of 693

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. Issues w/ 3.6.1 - 3.6.5

    Started by john_hartman, 10-19-2009 09:53 AM
    14 Pages
    1 2 3 ... 14
    • Replies: 130
    • Views: 11,195
    01-05-2010, 10:56 PM Go to last post
  2. Strange noise and nasty vibration

    Started by Randy Bogardus, 03-06-2014 02:22 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 64
    • Views: 7,373
    03-11-2014, 05:47 PM Go to last post
  3. Communication issue? Grind noise, then position loss

    Started by Brett1970, 02-15-2012 10:28 PM
    6 Pages
    1 2 3 ... 6
    • Replies: 57
    • Views: 11,367
    04-21-2012, 07:26 PM Go to last post
  4. Off Center

    Started by pappybaynes, 08-16-2014 05:38 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 44
    • Views: 6,805
    08-29-2014, 11:57 AM Go to last post
  5. static causing communication problems...again

    Started by bking1836, 10-17-2018 01:30 PM
    5 Pages
    1 2 3 ... 5
    • Replies: 44
    • Views: 5,754
    11-05-2018, 09:00 PM Go to last post
  6. Thumbs down I'm loosing it...

    Started by paco, 03-25-2010 11:34 PM
    5 Pages
    1 2 3 ... 5
    frustration
    • Replies: 43
    • Views: 14,408
    07-16-2010, 08:43 AM Go to last post
  7. Angry Ready to give up on HSD

    Started by Eppert, 06-24-2012 09:15 AM
    5 Pages
    1 2 3 ... 5
    spindle
    • Replies: 43
    • Views: 11,789
    04-24-2013, 12:06 AM Go to last post
  8. Really Need Help!

    Started by kubotaman, 04-29-2009 10:30 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 37
    • Views: 5,317
    05-02-2009, 12:32 PM Go to last post
  9. X/Y Motors Stalling

    Started by jdervin, 12-04-2010 10:51 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 37
    • Views: 9,511
    12-20-2010, 11:03 AM Go to last post
  10. Question What's causing this?

    Started by dhunt, 06-06-2011 01:51 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 37
    • Views: 8,008
    06-08-2011, 06:45 PM Go to last post
  11. SERIOUS violation of safety...

    Started by harryball, 10-24-2009 02:51 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 36
    • Views: 4,751
    11-03-2009, 10:21 AM Go to last post
  12. Shopbot "Jerking" After 3 minutes of use

    Started by Nstep007, 07-07-2017 09:48 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 36
    • Views: 4,854
    07-12-2017, 12:46 PM Go to last post
  13. Version 3.8.10

    Started by angelosart, 01-30-2014 04:20 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 6,470
    03-18-2014, 05:12 PM Go to last post
  14. Z Adjustment Question

    Started by sevans, 04-12-2018 11:00 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 4,131
    04-17-2018, 09:22 AM Go to last post
  15. Complete Shutdown

    Started by Shayne Jenkins, 12-18-2018 03:12 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 19,043
    01-28-2019, 05:06 PM Go to last post
  16. Losing Communication

    Started by Tim Summerer, 12-06-2012 05:50 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 33
    • Views: 12,401
    12-31-2012, 03:46 PM Go to last post
  17. Question PRS Alpha Missing Steps

    Started by chubb, 01-12-2014 02:27 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 33
    • Views: 8,324
    02-08-2015, 10:54 AM Go to last post
  18. No reset

    Started by Stagecraft, 01-20-2011 07:45 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 5,393
    01-22-2011, 11:33 AM Go to last post
  19. The yellow screen of death!

    Started by steve, 07-08-2011 03:49 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 6,291
    07-13-2011, 10:34 AM Go to last post
  20. Multipass Cut Through - Not Retracing in the same spot.

    Started by TNWALKINGHORSE, 03-30-2015 11:49 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 15,178
    04-12-2015, 11:49 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •