Page 1 of 34 12311 ... LastLast
Threads 1 to 20 of 668

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. YZ Car Lower Wheel Bearings

    Started by sevans, Yesterday 07:05 PM
    • Replies: 2
    • Views: 61
    Yesterday, 08:36 PM Go to last post
  2. Gusset T Nut Broken

    Started by sevans, 04-17-2018 05:24 PM
    • Replies: 1
    • Views: 107
    04-17-2018, 06:03 PM Go to last post
  3. Z Adjustment Question

    Started by sevans, 04-12-2018 11:00 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 1,073
    04-17-2018, 09:22 AM Go to last post
  4. Unhappy Z jogs too high after update

    Started by ger.wat, 04-02-2018 02:14 PM
    top limit, travel, z axis
    • Replies: 7
    • Views: 480
    04-15-2018, 03:04 PM Go to last post
  5. Z-Zero plate wire came out

    Started by tri4sale, 04-01-2018 10:43 PM
    • Replies: 4
    • Views: 263
    04-03-2018, 01:00 PM Go to last post
  6. Offsets while running, but jogs home correctly

    Started by harryball, 02-21-2018 11:44 AM
    • Replies: 6
    • Views: 726
    02-23-2018, 12:21 PM Go to last post
  7. Communication Error

    Started by stevenblake, 02-18-2018 02:08 PM
    comm error, communication problem, prs, troubleshooting, usb
    • Replies: 8
    • Views: 622
    02-21-2018, 01:42 PM Go to last post
  8. Spindle turning off during cut

    Started by bking1836, 01-18-2018 03:59 PM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 2,192
    01-31-2018, 11:36 PM Go to last post
  9. Resister for Gecko drive G203V

    Started by cwfreitas, 01-27-2018 06:04 PM
    • Replies: 5
    • Views: 348
    01-28-2018, 11:45 PM Go to last post
  10. Z Zero question

    Started by terryjones, 12-31-2017 04:38 PM
    • Replies: 2
    • Views: 447
    12-31-2017, 06:11 PM Go to last post
  11. cutter veering off circle

    Started by bob_reda, 12-27-2017 09:40 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 800
    12-30-2017, 12:58 PM Go to last post
    • Replies: 3
    • Views: 278
    12-29-2017, 03:40 PM Go to last post
  12. Bit PCL583659 1/16" Ball V Carve

    Started by Wilboy64, 12-06-2017 10:09 AM
    • Replies: 9
    • Views: 815
    12-09-2017, 08:58 PM Go to last post
  13. V90 bit not making clean cuts

    Started by DavidZ, 12-04-2017 09:11 PM
    • Replies: 2
    • Views: 385
    12-05-2017, 11:41 AM Go to last post
  14. Z axis command all by it's own!

    Started by letterman7, 10-16-2017 11:13 AM
    • Replies: 4
    • Views: 740
    10-18-2017, 07:30 AM Go to last post
  15. Driver Alarm

    Started by mrsoliver, 10-13-2017 03:17 PM
    prt alpha driver alarm
    • Replies: 1
    • Views: 264
    10-13-2017, 04:16 PM Go to last post
  16. zero plate not zeros

    Started by Alan m, 09-30-2017 05:19 PM
    • Replies: 3
    • Views: 492
    10-01-2017, 09:21 AM Go to last post
  17. Z Axis Trouble

    Started by pro70z28, 09-30-2017 09:21 AM
    • Replies: 3
    • Views: 427
    09-30-2017, 08:13 PM Go to last post
  18. gantry wont stop when using key pad

    Started by Alan m, 08-27-2017 09:05 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 827
    09-30-2017, 05:16 PM Go to last post
  19. Desktop Porter Cable Router Won't Turn On

    Started by Brett Whitman, 09-03-2017 07:15 PM
    • Replies: 3
    • Views: 597
    09-09-2017, 06:57 AM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •