Page 1 of 34 12311 ... LastLast
Threads 1 to 20 of 676

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. Question problems with arcs

    Started by a_custom_build, 07-15-2018 10:38 PM
    2 Pages
    1 2
    arc, circle, problem, test
    • Replies: 11
    • Views: 1,020
    07-31-2018, 08:14 AM Go to last post
  2. Shopbot never cut flat

    Started by ClayM325, 06-06-2018 10:04 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 1,522
    07-19-2018, 12:41 AM Go to last post
  3. USB transmission times

    Started by NicholasB, 06-27-2018 07:20 PM
    • Replies: 9
    • Views: 569
    07-18-2018, 03:05 PM Go to last post
  4. X, Y zeros not always the same?

    Started by ClayM325, 06-13-2018 12:32 PM
    • Replies: 7
    • Views: 576
    07-17-2018, 09:45 PM Go to last post
  5. shopbot

    Started by hknisely, 07-07-2018 03:43 PM
    • Replies: 4
    • Views: 362
    07-12-2018, 08:14 AM Go to last post
  6. Stepmotor issue...maybe..? Help!

    Started by Djed, 06-30-2018 07:40 PM
    • Replies: 2
    • Views: 246
    07-01-2018, 10:47 AM Go to last post
    • Replies: 1
    • Views: 233
    06-11-2018, 10:46 AM Go to last post
    • Replies: 2
    • Views: 554
    05-10-2018, 12:51 AM Go to last post
  7. YZ Car Lower Wheel Bearings

    Started by sevans, 04-19-2018 07:05 PM
    • Replies: 2
    • Views: 450
    04-19-2018, 08:36 PM Go to last post
  8. Gusset T Nut Broken

    Started by sevans, 04-17-2018 05:24 PM
    • Replies: 1
    • Views: 353
    04-17-2018, 06:03 PM Go to last post
  9. Z Adjustment Question

    Started by sevans, 04-12-2018 11:00 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 35
    • Views: 2,095
    04-17-2018, 09:22 AM Go to last post
  10. Unhappy Z jogs too high after update

    Started by ger.wat, 04-02-2018 02:14 PM
    top limit, travel, z axis
    • Replies: 7
    • Views: 852
    04-15-2018, 03:04 PM Go to last post
  11. Z-Zero plate wire came out

    Started by tri4sale, 04-01-2018 10:43 PM
    • Replies: 4
    • Views: 552
    04-03-2018, 01:00 PM Go to last post
  12. Offsets while running, but jogs home correctly

    Started by harryball, 02-21-2018 10:44 AM
    • Replies: 6
    • Views: 976
    02-23-2018, 11:21 AM Go to last post
  13. Communication Error

    Started by stevenblake, 02-18-2018 01:08 PM
    comm error, communication problem, prs, troubleshooting, usb
    • Replies: 8
    • Views: 1,064
    02-21-2018, 12:42 PM Go to last post
  14. Spindle turning off during cut

    Started by bking1836, 01-18-2018 02:59 PM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 3,148
    01-31-2018, 10:36 PM Go to last post
  15. Resister for Gecko drive G203V

    Started by cwfreitas, 01-27-2018 05:04 PM
    • Replies: 5
    • Views: 623
    01-28-2018, 10:45 PM Go to last post
  16. Z Zero question

    Started by terryjones, 12-31-2017 03:38 PM
    • Replies: 2
    • Views: 661
    12-31-2017, 05:11 PM Go to last post
  17. cutter veering off circle

    Started by bob_reda, 12-27-2017 08:40 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 1,198
    12-30-2017, 11:58 AM Go to last post
    • Replies: 3
    • Views: 491
    12-29-2017, 02:40 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •