Page 11 of 37 FirstFirst ... 91011121321 ... LastLast
Threads 201 to 220 of 739

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. Strange new problem

    Started by tlempicke, 05-17-2015 04:25 PM
    2 Pages •
    1 2
    • Replies: 13
    • Views: 7,247
    kevin
    05-19-2015, 06:30 PM Go to last post

  2. Variation in Calibration (X & Y)

    Started by gregg, 05-18-2015 04:10 PM
    • Replies: 4
    • Views: 3,046
    Brady Watson
    05-18-2015, 06:32 PM Go to last post

  3. Question Unit Values for Z and A are not the same

    Started by SparksStudios, 05-09-2015 05:31 PM
    • Replies: 3
    • Views: 2,756
    SparksStudios
    05-12-2015, 08:53 AM Go to last post

  4. Runtime error 6 overflow- resolved in Icelandic

    Started by willnewton, 04-27-2015 11:04 PM
    • Replies: 2
    • Views: 2,772
    willnewton
    05-12-2015, 12:14 AM Go to last post

  5. USB not conectting

    Started by Almost Scientific, 10-22-2012 05:35 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 4,546
    Vector Concepts
    05-04-2015, 06:02 PM Go to last post

  6. control over B axis

    Started by markevans, 05-02-2015 07:03 PM
    • Replies: 4
    • Views: 2,296
    markevans
    05-03-2015, 11:21 PM Go to last post

  7. Vacuum Table Issues

    Started by ChrisR, 04-15-2015 11:16 AM
    • Replies: 6
    • Views: 4,485
    ChrisR
    04-20-2015, 03:31 PM Go to last post

  8. Multipass Cut Through - Not Retracing in the same spot.

    Started by TNWALKINGHORSE, 03-30-2015 11:49 PM
    4 Pages •
    1 2 3 ... 4
    multipass, prt 9 Attachment(s)
    • Replies: 30
    • Views: 27,861
    donek
    04-12-2015, 11:49 PM Go to last post

  9. Z axis zeroing and drifting deeper problems

    Started by bbobmc, 04-11-2015 02:48 PM
    • Replies: 6
    • Views: 6,243
    bbobmc
    04-12-2015, 10:49 PM Go to last post

  10. Loss of Vacuum Hold Down

    Started by jdervin, 04-11-2015 02:49 PM
    • Replies: 5
    • Views: 2,664
    bleeth
    04-12-2015, 07:50 AM Go to last post

  11. X2 motor turns freely

    Started by asemcollc, 04-11-2015 02:10 PM
    stepper motors
    • Replies: 2
    • Views: 2,013
    asemcollc
    04-12-2015, 06:59 AM Go to last post

  12. Keyboard move issues

    Started by wwaldner, 03-28-2015 10:35 AM
    2 Pages •
    1 2
    keyboard freeze
    • Replies: 11
    • Views: 6,994
    Brady Watson
    04-01-2015, 04:41 PM Go to last post

  13. Hogging Out - Saving Time - then finish bit

    Started by TNWALKINGHORSE, 03-31-2015 09:49 PM
    • Replies: 2
    • Views: 2,488
    Kyle Stapleton
    03-31-2015, 10:15 PM Go to last post

  14. Bot kept stopping during job

    Started by barrowj, 03-30-2015 09:57 AM
    2 Attachment(s)
    • Replies: 5
    • Views: 3,562
    David Iannone
    03-31-2015, 05:44 PM Go to last post

  15. z axis not responding

    Started by gene, 03-19-2015 12:56 AM
    • Replies: 9
    • Views: 8,988
    gene
    03-20-2015, 03:15 PM Go to last post

  16. Default Ramp settings in 3.8.26?

    Started by Mayo, 03-12-2015 06:25 PM
    2 Attachment(s)
    • Replies: 7
    • Views: 4,538
    Brady Watson
    03-16-2015, 09:44 PM Go to last post

  17. Question Proper Setup from a Newbie

    Started by TNWALKINGHORSE, 03-14-2015 12:24 AM
    2 Attachment(s)
    • Replies: 0
    • Views: 1,662
    TNWALKINGHORSE
    03-14-2015, 12:24 AM Go to last post

  18. X-axis slow down while cutting file??

    Started by blackhawk, 09-18-2013 09:31 AM
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 11
    • Views: 7,446
    Brady Watson
    03-12-2015, 05:41 PM Go to last post

  19. Broken control box switch

    Started by steve fedor, 03-10-2015 08:03 PM
    4 Attachment(s)
    • Replies: 5
    • Views: 3,253
    steve fedor
    03-11-2015, 08:46 PM Go to last post

  20. Smooth Cuts in Hardwood?

    Started by Lee Miller, 02-26-2015 01:19 AM
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 18
    • Views: 10,604
    scottp55
    03-02-2015, 07:34 AM Go to last post
Page 11 of 37 FirstFirst ... 91011121321 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules