Page 2 of 37 FirstFirst 123412 ... LastLast
Threads 21 to 40 of 739

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. ANOTHER Vista issue!

    Started by chuckster, 01-04-2009 07:47 PM
    • Replies: 8
    • Views: 2,956
    chuckster
    02-14-2009, 01:32 AM Go to last post

  2. Communication Problem?

    Started by erik_f, 02-22-2009 12:03 AM
    • Replies: 0
    • Views: 2,341
    erik_f
    02-22-2009, 12:03 AM Go to last post

  3. Y axis looses postion on diagonal cuts

    Started by fsrdoug, 02-21-2009 07:18 PM
    • Replies: 4
    • Views: 2,435
    erik_f
    02-22-2009, 10:21 PM Go to last post

  4. Lost connection, how to avoid?

    Started by lto, 02-23-2009 11:18 AM
    • Replies: 6
    • Views: 3,286
    nat_wheatley
    02-23-2009, 10:22 PM Go to last post

  5. Unit Values - would you change them?

    Started by drodda, 02-27-2009 02:39 PM
    • Replies: 1
    • Views: 1,971
    rhfurniture
    02-28-2009, 11:03 AM Go to last post

  6. 12" in SB = 8 5/16 in the real world

    Started by khaos, 03-01-2009 01:11 PM
    • Replies: 1
    • Views: 2,237
    khaos
    03-01-2009, 05:52 PM Go to last post

  7. Zeroing x and y

    Started by jerry_stanek, 02-28-2009 07:50 PM
    • Replies: 3
    • Views: 2,562
    bernott
    03-02-2009, 09:38 PM Go to last post

  8. "locating tool", then computer locks up

    Started by mjindustry, 03-01-2009 12:10 PM
    • Replies: 8
    • Views: 3,252
    mjindustry
    03-05-2009, 09:50 AM Go to last post

  9. Opening dxf in vector

    Started by donj93, 03-04-2009 03:05 PM
    • Replies: 4
    • Views: 2,552
    srwtlc
    03-06-2009, 09:52 AM Go to last post

  10. XYzero.sbp variable input file

    Started by kc10flteng, 03-10-2009 07:06 PM
    • Replies: 1
    • Views: 2,299
    srwtlc
    03-10-2009, 07:49 PM Go to last post

  11. Shopbot not following Tollpath in one direction

    Started by ffaelan, 03-11-2009 07:03 PM
    2 Pages •
    1 2
    • Replies: 11
    • Views: 5,158
    Brady Watson
    03-13-2009, 05:05 PM Go to last post

  12. Zero Z axis Fine Point Bits

    Started by majohnson, 03-15-2009 10:32 AM
    • Replies: 7
    • Views: 3,338
    tparr
    03-16-2009, 02:15 PM Go to last post

  13. Error 91

    Started by jimmya, 03-07-2009 07:41 AM
    1 Attachment(s)
    • Replies: 5
    • Views: 2,786
    jimmya
    03-17-2009, 05:02 AM Go to last post

  14. Z depth...yet again!

    Started by letterman7, 11-12-2008 12:40 PM
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 15
    • Views: 5,798
    hykambois
    03-30-2009, 12:30 PM Go to last post

  15. LIMIT SWITCH HIT...LOSING STEPS!

    Started by sevans, 04-09-2009 04:15 PM
    • Replies: 3
    • Views: 4,246
    jerry_stanek
    04-09-2009, 05:55 PM Go to last post

  16. Problems with erratic cutting on my PRT with 4G

    Started by terryjones, 04-08-2009 11:54 PM
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 14
    • Views: 5,659
    erik_f
    04-10-2009, 10:52 PM Go to last post

  17. Motor won't reverse

    Started by metalmaker, 04-11-2009 03:49 PM
    • Replies: 1
    • Views: 1,959
    metalmaker
    04-12-2009, 05:41 PM Go to last post

  18. Shopbot pausing mid file

    Started by gregg, 04-14-2009 01:46 PM
    • Replies: 8
    • Views: 3,405
    khaos
    04-16-2009, 03:02 PM Go to last post

  19. I could use some help solving some problems.

    Started by knight_toolworks, 04-05-2009 03:29 PM
    2 Pages •
    1 2
    • Replies: 13
    • Views: 5,146
    knight_toolworks
    04-17-2009, 02:21 AM Go to last post

  20. Run time error '9'

    Started by casey_h, 03-28-2008 05:44 PM
    • Replies: 2
    • Views: 2,579
    tomf
    04-20-2009, 12:42 PM Go to last post
Page 2 of 37 FirstFirst 123412 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules