Page 1 of 5 123 ... LastLast
Threads 1 to 20 of 100

Forum: ShopBot Control Software v3

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. safe z change for cutter clearace

    Started by hunterland, 03-17-2024 04:22 PM
    • Replies: 2
    • Views: 215
    bill.young
    03-22-2024, 10:08 AM Go to last post

  2. Old computer bit the dust

    Started by jim shula, 02-24-2024 10:26 PM
    • Replies: 0
    • Views: 117
    jim shula
    02-24-2024, 10:26 PM Go to last post

  3. Relationshp between ShopBot VR values and Aspire Bit Settings

    Started by jwinslow, 04-28-2023 01:24 PM
    extreme detail
    • Replies: 5
    • Views: 1,909
    rcnewcomb
    05-03-2023, 06:29 PM Go to last post

  4. Person in So Cal needed to troubleshoot SB3 software

    Started by New to all this, 01-29-2023 07:53 PM
    help setup shopbot, prs alpha, sb3, trouble shoot 3 Attachment(s)
    • Replies: 4
    • Views: 780
    New to all this
    01-30-2023, 04:37 PM Go to last post

  5. PRT control software installation

    Started by pro70z28, 09-26-2022 10:34 AM
    • Replies: 3
    • Views: 962
    bill.young
    09-26-2022, 12:36 PM Go to last post

  6. Lightbulb Is there a carriage return character in INPUT box text?

    Started by Scott216, 08-15-2022 06:32 AM
    • Replies: 4
    • Views: 851
    EricSchimel
    08-17-2022, 10:33 AM Go to last post

  7. having difficulties reading CSV data from sbp file...

    Started by Marc F. Lupien, 06-13-2021 12:41 PM
    file reading, programming
    • Replies: 2
    • Views: 1,939
    Marc F. Lupien
    06-13-2021, 09:38 PM Go to last post

  8. Go home

    Started by david_white, 03-04-2021 09:50 AM
    • Replies: 5
    • Views: 5,416
    GaryGraff
    03-05-2021, 08:14 AM Go to last post

  9. How to check for offset-mode inside a sbp file... ?

    Started by Marc F. Lupien, 07-18-2020 12:18 PM
    2 Pages •
    1 2
    • Replies: 16
    • Views: 8,029
    EricSchimel
    07-27-2020, 01:22 PM Go to last post

  10. other hardware

    Started by ddrumguy, 05-10-2019 02:02 AM
    • Replies: 4
    • Views: 9,119
    steve_g
    05-12-2019, 06:21 AM Go to last post

  11. System variables question...

    Started by geneb, 03-15-2019 05:40 PM
    • Replies: 4
    • Views: 14,236
    geneb
    03-25-2019, 11:45 AM Go to last post

  12. Rank Beginner Here

    Started by Ron Sommers, 09-20-2018 01:11 PM
    3 Pages •
    1 2 3
    • Replies: 21
    • Views: 12,385
    bking1836
    09-26-2018, 10:55 AM Go to last post

  13. Tool path dropping into "ATC_XYZ_Home.sbp" unexpectedly

    Started by alanmcw, 02-22-2018 12:03 PM
    • Replies: 1
    • Views: 5,397
    Brady Watson
    02-22-2018, 01:30 PM Go to last post

  14. “nudge” command question...

    Started by steve_g, 01-08-2018 07:05 PM
    • Replies: 3
    • Views: 20,107
    scottp55
    01-09-2018, 09:53 AM Go to last post

  15. Changing safe z in VC (temporarily)

    Started by dbrannen, 01-18-2017 09:11 AM
    2 Attachment(s)
    • Replies: 5
    • Views: 7,624
    dbrannen
    04-10-2017, 04:27 PM Go to last post

  16. Angry Dual Spindle RPM Control

    Started by ADAPT_Shop-Brady, 03-13-2017 11:41 AM
    dual spindles
    • Replies: 1
    • Views: 2,391
    Gary Campbell
    03-13-2017, 05:28 PM Go to last post

  17. can i create a tool path that i can follow manually

    Started by Alan m, 01-21-2017 07:51 PM
    2 Pages •
    1 2
    6 Attachment(s)
    • Replies: 15
    • Views: 10,333
    khaos
    02-02-2017, 05:55 PM Go to last post

  18. How might I change the position of a piece from a G-code file in SB3?

    Started by carolinasmith, 01-07-2017 03:42 AM
    2 Pages •
    1 2
    • Replies: 13
    • Views: 9,302
    scottp55
    01-09-2017, 07:58 PM Go to last post

  19. Question Removing the Router/Spindle message box

    Started by Jesse@AirPower, 10-26-2016 09:26 AM
    programming 1 Attachment(s)
    • Replies: 6
    • Views: 5,464
    BrandanS
    10-26-2016, 01:00 PM Go to last post

  20. SB3 'Material Size' different than Aspire 8.5 'Job Size and Position, how to fix?

    Started by carolinasmith, 10-06-2016 12:00 AM
    4 Attachment(s)
    • Replies: 5
    • Views: 5,005
    carolinasmith
    10-06-2016, 08:35 PM Go to last post
Page 1 of 5 123 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules