Thanks. It was me being a dummy. I didn't even think to look at the speeds, and it was in inches per minute. I typically set feedrates in inches per second, so I had it going 2 inches per minute. ...
Type: Posts; User: BoilermakerAndy
Thanks. It was me being a dummy. I didn't even think to look at the speeds, and it was in inches per minute. I typically set feedrates in inches per second, so I had it going 2 inches per minute. ...
Hi there.
By reading various threads, I was able to create a 1/4" round-over "form tool" in V-Carve Pro. After setting it up and previewing the toolpath, it looked perfect.
When I tried to run...
So, I have a Becker pump vacuum system for my table. I recently completely re-built the table of the machine I bought used, and I went from pulling maybe 10" of vacuum to almost 25" with a freshly...
Man, I could've used this post 9 months ago. Luckily, I was able to have two non-functional Porter Cable routers rebuilt.
Then, of course, I sold that ShopBot and got a PRSAlpha ATC.
Hi everyone.
I bought a used 2016 PRSAlpha ATC back in mid April, which came with a Becker vacuum pump. In April/May, it was pulling about 10-12" of vacuum for a sheet of plywood, and about 15"...
Good morning.
I recently acquired a 2016 PRS Alpha ATC. I was experimenting with a product that is symmetric. I ran it face up for one operation, then flipped it over for a secondary operation. ...
This won't work. I have two motors in one chamber on my old system. The vacuum created by the running motors will cause the un-powered motors to spin backwards, allowing air in that way as a...
Hey Red. That very well may be the case. My vacuum numbers are very similar covered vs. uncovered. Also, I just noticed that the v-shaped support under that area is missing all the bolts on one...
I have the pressure plate on the ATC, but I use the Z-Zero plate on the table.
I am leaning towards a plenum problem. I just re-zeroed to the table and ran this pattern on the blank table with...
Thanks Ken. Yea, that start depth is always zero for me.
Thanks for the pic. I've verified with Vectric that the post processor they have for V-Carve PRO is, in fact, the correct one for the ATC. It has all the proper call-outs for the ATC. Anyway, none...
I tried to use my Micrometer to measure the Z travel. With the imperfect method of measurement it seems to be accurate in terms of the stepper values. It certainly does not explain the pattern from...
So, I turn the vacuum system on when skimming, which I learned with my last vacuum table. Now, this seems preposterous to me, but I'll go ahead and say it.....
Is it remotely possible that the...
34555
34556
Thanks for all your input.
The guy who sold it to me (and delivered it) helped me set it up. We ran the CN74 program to calibrate the clip locations. We loaded the tools into the collets and ran...
Yes, I ran the C73 table offset for the zero plate after skimming, and all the bits have been zeroed correctly.
I'm refining my last post a bit.
My machine is consistently NOT cutting through the material when it should.
My machine is a 2016 PRS Alpha ATC. I have skimmed the spoilboard. I program the...
Never mind. Googled it. Got it.
Since I bought this used, and therefore am not terribly familiar with the assembly, can you clarify a little? As in, what's a "grub screw".
Pardon my ignorance.
Hmmmm........
I'll have to check that.....
I just took possession of a 2016 PRSAlpha ATC, replacing my OLD (circa 2001) PRT. It's taking a bit of getting used to, unfortunately. I did find out that I have a bad connector on the Z-Zero...
Yes, that's what I believe as well, though I imagine there is then SOME miniscule amount that makes it through to the air. Can you recommend which oil/water separator to use? Oh, and thanks for the...
Let's see if anyone sees this add on to an old post.
Most of the compressors I see are oil lubricated, which ShopBot says not to use. Can anyone recommend a specific compressor, preferably not...
6 IPS???? Wow. What depth do you cut per pass?
I'm probably cutting too much at a time. In 3/4" pine (0.725" actual), I cut in two passes.....basically .375" per pass, but I'm only cutting at...
Thanks for the thoughtful response. I really do appreciate it. I do use a compression bit for certain applications. However, I'm currently running an OLD 4'x8' PRT (Circa 2003?) with the Porter...