Search:

Type: Posts; User: ken_rychlik

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    11
    Views
    511

    @Jerry, He is not on a shopbot controller, so...

    @Jerry, He is not on a shopbot controller, so who knows how they are mounted. I'm guessing a home made control box based on the pmdx board he mentioned.
  2. It's still available and I'm looking for a new...

    It's still available and I'm looking for a new home for it.
  3. Replies
    8
    Views
    395

    So if you are not on the shopbot software, I...

    So if you are not on the shopbot software, I would put leadshine drives in it. Smooth, quiet, and less motor heating. DM556E or DM860E Depending on your supply voltage. Look up automation direct
  4. Replies
    8
    Views
    395

    yes switching the red and blue in the plug should...

    yes switching the red and blue in the plug should make it run the opposite way. If you are comfortable with a meter, each pair has continuity and no continuity between each other.
  5. Replies
    8
    Views
    395

    They are paired in the plug. Two on one side and...

    They are paired in the plug. Two on one side and two on the other. Reverse either pair. They come out very easy with a tab you push in on the connector going into the controller.
  6. Buddy 2x4 with spindle for sale Near Houston

    For Sale. 2008 Model Shopbot Buddy prs in great working order. It has a hsd spindle with Yaskawa drive for it. Very low hours on the machine. It is fixed up with a table on the end of it for the...
  7. Replies
    0
    Views
    292

    2x4 Buddy Near Houston 5000

    2008 Model Shopbot Buddy prs in great working order. It has a hsd spindle with Yaskawa drive for it. Very low hours on the machine. It is fixed up with a table on the end of it for the keyboard,...
  8. Replies
    3
    Views
    518

    Modify the post processor of the design software....

    Modify the post processor of the design software. If you are using vectric, lots of us can help you make it do what you want. If you pm me we can email back and fourth and make it happen easily.
  9. Replies
    3
    Views
    377

    I sent you a message. If you would mail it, I...

    I sent you a message. If you would mail it, I would cover shipping on the vfd and cable. The spindle is kind of unusable for a normal machine, so I'm not sure who would use that.
  10. Replies
    0
    Views
    285

    4g PRS Controller from a 2008 buddy

    PRS Standard 4g controller for sale. Working condition but dusty. I can do a video call to show you it is currently running a machine. The lady this came from said it has about 20 hrs on it and...
  11. pm sent to you

    pm sent to you
  12. Replies
    1
    Views
    436

    SOLD Have fun with it Todd

    SOLD Have fun with it Todd
  13. Replies
    1
    Views
    436

    2012 Desktop 24x18 Near Houston

    This is a little interesting as it used to belong to autodesk which are the makers of fusion 360. I think they just used it for testing as it looks barely used. Asking $3900 without pc or $4200 with...
  14. Thread: Geckodrive

    by ken_rychlik
    Replies
    4
    Views
    433

    If you have a shorted wire to the motor, or...

    If you have a shorted wire to the motor, or shorted windings on that motor, it might blow another new one as well. I went to Leadshine drives, because of so many bad Gecko's I've had to deal with. I...
  15. If you still have it I’ll take it. I sent you my...

    If you still have it I’ll take it. I sent you my number on pm
  16. Thread: Forum Use

    by ken_rychlik
    Replies
    13
    Views
    1,712

    Monty, wincnc or acorn are not hard, but they...

    Monty, wincnc or acorn are not hard, but they are different. Each takes it's getting used to. As for the big electricity, quite often you can convert or run the bigger machines from single phase. ...
  17. Replies
    2
    Views
    832

    Older generation than the buddy. Probably worth...

    Older generation than the buddy. Probably worth 2-3k depending on if it's running and useable.
  18. Replies
    11
    Views
    5,047

    I ran with a motor plumbed to each zone on...

    I ran with a motor plumbed to each zone on several machines. Then I turn on what zones I'm working within. Cheap and effective.
  19. Odd size for most folks. I would say 7k if it...

    Odd size for most folks. I would say 7k if it just has a router, and 8 or 9 with a spindle depending on size.
  20. I would unhook the z motor and check for smooth...

    I would unhook the z motor and check for smooth movement of the Z slide. Make sure the springs are carrying most of the weight so the motor is not working to hard. Sometimes the bit slips in the...
  21. One of the connectors or motors had to have been...

    One of the connectors or motors had to have been changed somewhere. Most other software controllers can change motor direction in the settings, but I'm not aware of that in SB.
  22. Unplug one of them from the board. Use an ohm...

    Unplug one of them from the board. Use an ohm meter to determine two pair of coils. reverse either of the pair that are on one coil and it will run the other way.
  23. I tried to contact you when it was on craigslist...

    I tried to contact you when it was on craigslist for 1000 but you never responded
  24. Replies
    9
    Views
    3,311

    I never had a need for it, but I had a spare...

    I never had a need for it, but I had a spare motor on hand. 150 dollars was cheap insurance and easier than extra plumbing.
  25. Replies
    9
    Views
    3,311

    I did per quad with electrical swithes to use the...

    I did per quad with electrical swithes to use the areas needed
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4