Search:

Type: Posts; User: knight_toolworks

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    9
    Views
    412

    well unless it is a 4x8 sheet. a compromise is to...

    well unless it is a 4x8 sheet. a compromise is to spray one side of the material or table with strong contact glue and then vacuum it down. that works well but it is a bit messy and it can get...
  2. Replies
    9
    Views
    412

    been using it for years. you still need some way...

    been using it for years. you still need some way to hold the sheet in place. I use it keep thin plastic from lifting up when I cut it. but there are other methods depending on what your cutting....
  3. Replies
    10
    Views
    841

    he machine will jam up before that. t

    he machine will jam up before that.
    t
  4. Replies
    10
    Views
    841

    even at that I don't think I am pushing things. I...

    even at that I don't think I am pushing things. I think the shopbot will run out of power before the spindle does.
  5. Replies
    10
    Views
    841

    with the 4hp hsd I can take 1/8" off on wood...

    with the 4hp hsd I can take 1/8" off on wood surfacing with a 2.5" bit at 6ips
  6. I leaned that the hard way (G) I had a lot of...

    I leaned that the hard way (G) I had a lot of 3/4" hdpe left over. you can sand it with a really course paper to give it tooth.
  7. the problem I see is without the texture...

    the problem I see is without the texture commercial cutting boards have your food slides off.
  8. Replies
    15
    Views
    931

    good to know. I know it was hard to fork out for...

    good to know. I know it was hard to fork out for a new spindle a couple years ago.
  9. Replies
    12
    Views
    1,820

    these will be lighted. but they are going to use...

    these will be lighted. but they are going to use a gray stain on the wood so it wont contrast well. I was worried about wood movement too. so I used cedar and planed it down to 1/8" as thats the...
  10. Replies
    12
    Views
    1,820

    ok finally customer got his stuff together. he ...

    ok finally customer got his stuff together. he is a new sign guy so he needs hand holding. I decided to go with wood as he is not skilled at painting I used west systems g flex epoxy to glue 1/8"...
  11. Replies
    3
    Views
    382

    I have cut a lot of this. feel lucky its s 1/8"...

    I have cut a lot of this. feel lucky its s 1/8" most of what I cut is .03 thick and it is hard to hold in place and I often need to use a pressure foot. but I can usually get away with a 1/16"...
  12. Replies
    9
    Views
    1,270

    for wood I often us a bradpoint bit 3500 rpms it...

    for wood I often us a bradpoint bit 3500 rpms it works well and good ones are easy to get locally. a boring bit would be nice if I knew ahead of time
  13. Replies
    8
    Views
    1,141

    it is dc 24v but the extra wire is for speed...

    it is dc 24v but the extra wire is for speed control.
  14. Replies
    8
    Views
    1,141

    well it is a oddball 60mm x25mm 24v but 3 wire...

    well it is a oddball 60mm x25mm 24v but 3 wire plenty of two wire ones but hard to find all those
  15. Replies
    8
    Views
    1,141

    ya I will take it off when I am done today and...

    ya I will take it off when I am done today and clean everything. hey its 12 years old with lots of dust running through it it has lasted well.
  16. Replies
    8
    Views
    1,141

    ya found the manual but no fans in the US. I...

    ya found the manual but no fans in the US. I found the fan pops out without taking it apart.so I will try cleaning it.
  17. Replies
    8
    Views
    1,141

    fan for yaskawa v7-4x fan vfd?

    I have noticed the fan on mine is louder. hey only 12 years old so no complaints.
  18. Replies
    12
    Views
    1,820

    my customer has been dragging his feet. but we...

    my customer has been dragging his feet. but we were going to use some of this flooring from home depot. but another sign customer told me about precision board with a wood grain texture pre painted.
  19. Replies
    8
    Views
    976

    I can export it into a dxf or pdf. its a easy...

    I can export it into a dxf or pdf. its a easy build and works great. message me and I will give you my email address and info on how to build it.
  20. Replies
    7
    Views
    1,014

    I have cut years with 200 cfms and at most 8"...

    I have cut years with 200 cfms and at most 8" finally built a black box that is super quiet only 76 db's for around 700 total its to about 82 with all 4 motors running. l. but of course the motors...
  21. Replies
    8
    Views
    976

    well wth a seal between the box and the lid I got...

    well wth a seal between the box and the lid I got another 2db's reduction. now it is on par or lower then the whole house vacuums and about 1/3 the cost.
  22. Replies
    8
    Views
    976

    I would not say a lot but overall maybe 2...

    I would not say a lot but overall maybe 2 decibels. I was too lazy too test with and without. the top reduces the noise from 92 to 78 on its won. I am debating on making another one with textured pdf...
  23. Replies
    8
    Views
    976

    the fellow that emailed me your email vanished...

    the fellow that emailed me your email vanished email me again and there is the file https://www.dropbox.com/s/oz2d750segq0flw/vac%20filter%20box%204%20motor.crv3d?dl=0
  24. Replies
    8
    Views
    976

    one more pic.

    one more pic.
  25. Replies
    8
    Views
    976

    more pics I wonder of a longer baffle on the top...

    more pics I wonder of a longer baffle on the top lid would do more since thats the biggest course of noise.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4