Anyone have a 3D file or source for 3D files. I need a dragon and a horse jumping for 2 upcoming projects. Striking out online. Anything you have available would be very much appreciated. PM me here...
Type: Posts; User: ColdBlooded
Anyone have a 3D file or source for 3D files. I need a dragon and a horse jumping for 2 upcoming projects. Striking out online. Anything you have available would be very much appreciated. PM me here...
Depth of cut is consistent. Problem you can't just go straight down. You will end up with a 90 degree at the top. Needs to cut wider then the bit in steps
I use this bit daily, just not with 2" thick materiel. I don't have a table saw that I would trust to make this cut. Only a small Dewalt. My alternative is clamps, guide board and a hand held. CNC...
I'm making a waterfall table with 2" maple. I can't figure out how to make a miter fold tool path using:
https://www.toolstoday.com/v-8762-rc-1028.html
How do you make a tool path that will...
I cut a vac table about 6 years ago using the standard shopbot program. Its that time again but I cant find the program ?? Anyone know where to find it in the software? Thanks
Anyone have any ideas on how I can open a .SLDPRT file in Aspire? Or a free online program to open it and save as an Aspire friendly file. My supplier gave me the file and they don't know what...
I'm having trouble opening or finding something to open a .SLDPRT file. Not sure if it's a bad file or done on a older version of the software. If anyone is good with Solid Works that can help...
Looking for someone with a indexer to cut a few flat top cones out of wood. These will be used as molds. Wood type does not matter as long as it's smooth and hard. Sample of what I need is 8"...
I'm trying to upgrade my Aspire. Not getting the best communication or assistance from Vetric. Version 1.0 is so old you can't upgrade online. I have not had the need to upgrade until now. I don't...
Thanks guys for the help. Parts turned out almost perfect. Needs a few tweaks and to tighten up my stepover but very nice. Thanks again. 2441924420
Brady, Thank you so much they are perfect. I'm going to need other sizes and would like some training on Aspire and the Indexer. I see you offer advanced training. What does it cost for someone to...
Sorry, not a video just showing a indexer. One showing how to fit large 24" diameter in the 12" indexer. I was searching for a video of someone cutting very large stock so I can get an idea of the...
Yes, exactly what I'm looking for. Since your drawing was exactly the same as the one posted in the 2nd post of this thread you can understand my confusion as to what you where asking for. Is it...
Thanks for the info. Had no idea a 6" can cut 12" diameter tubes. I was assuming a 6" cut 6". I will look into a indexer. Do you know of any videos showing one working? I need some more advanced...
...Helped....
24400See attached pen and paper diagram. Need 2 parts. The one in blue Part A is outside. Part B in red and inside part. Both parts are 3.5"Lx3.5"Wx3/8" thick acrylic. Need both parts to glue on the...
I had thought about a indexer. I have a 6" bot so it would not help me cut 8"-14" tubes
All of the drawing in this thread are exactly what I need. Just in a file I can work with in my version. VERY OLD version 1.029
I did not ever say I expect someone to work for free. I have no problem paying for someones time. I am a newby to Aspire 3D tools. I looked at your sample drawing. It looks like one of the parts i'm...
This is not 100% ShopBot related. Anyone have any cleaver ideas to cut large acrylic tubes over 8". I cut a jig on my bot to hold the tube and mounted a router to the bottom. I hand rotate the tube...
3.5" square w/ .25 radius corners with 8" radius cut into .354 acrylic. I also need the reverse with 7.5" radius. I need a front and back flange to be glued to a 8"od acrylic tube for a flat surface...
Thanks again Scott for your help.
I am using a older version of Aspire and can not correctly make the part s I need. Anyone that works with the 3D tools that can help. Scott made me a sample file using a different software but I cant...
What was the process you used to create that part in Aspire
yes correct measurements and thanks for the help