Search:

3230832308
Worked like a charm
Hope the picture attached correctly

I am attempting to make a sleeve/holder for a metal tumbler.
Though I could cut the sleeve on my Desktop in halves and them glue them together.
If I can do it on the Shopbot the fitting could be...

Scott
Thank you will make the adjustments and see what happens

Cutting a 3D plaque on my desk top using Cherry
during the roughing was getting combo of chips and splinters
.
Now on the finishing cut I am getting ribbons instead of chips
the cut is good, not...

I am attempting to carve a presentation badge using Vectric Model Bade #5805 A
I am running Aspire 9.0
I was advised that a model can be taken apart using Aspire to make changes?
If this is true...

Scott
Thanks for the info
was cutting at 3.0ips at 12000rpm
New Onsrude Bit so I would not think sharpness an issue
will slow it down to 1ips and fiddle with the rpm
will try cutting across the...

Was cutting the lid for the Zin Garden Box, a Vecctric Project.
Using a 1/4 2 flut cutter
the Desktop Spindle was running at 210mhz

The attached pictures shows the cut, it did not cut the oak,...

Wanted to make new spoil board for my desk top
can't locate the SP file for cutting the DT Spoil Board
Can someone point me to the file
or send me a file

thanks

Scott
Thanks for the info and guidance, The stars are small to get the scale correct for my max 24" desktop
only 0.6945 tip to tip and shallow my Aspire 8.5 has the minimum depth of 0.196 to not...

Attempting to carve stars into a piece of Purple Heart
using 60 deg 1/2 V-Bit
RPM 14000

What would be a good feed and speed
thank you

Not Callous at all
Just did not know the details, my bad, not ShopBot at all and things break that is life
Just frustrated, but again that is life
HSD agrees with you, I called them yesterday and...

Sorry
The spindle is controlled by the VFD the software runs the tool pathing
I have a desktop and just learned that the Spindle is NOT covered under
The ShopBot warrenty
I ran the C5 Warm Up...

Fellow Shop Botters/Desktoo Users
Tech support has determined that the cause of the Spindle on my Desktop to overheat is most likely a barring issue. I received my Desktop in Dec 2013....

Brady
Thanks for the great suggestions
I don't think the bearings are bad, the spindle is smooth when turned by hand
it is quite when running
I will check the air flow IN the correct location...

Fellow Botters
The VFD error “EF” gremlin is still haunting my Desktop.
Tech support and I agree that this may be caused by the Spindle Overheating.
We have pretty much eliminated the normal...

JWA1156 in Miami


Still
having the EF (External Fault) error code, stopping the spindle
I have been able to catch it sometimes and safe the work
but others times lots of time and...

Scott

Thanks
Will try the UPS
Support did send some pictures of the wiring for me to check
but thy seemed ok
Thanks

Scott
It had a very fine glue line
as to the Desktop
It has to working levels
GREAT
as these plaques indicate
SCREWED UP
as the many scraps of wood and broken bits.

Still

Gary
Thanks
Have to use special software on my PC Monitor to magnify the image.
I am an Iraq Vet and Lost all sight in right eye and legally blind in the left.
Was introduced to wood work during...

Scott
The Police plaque is 15.25"
the JrJROTC Plaque is 14.75
both started with 1" Red Oak Base

My Brother In Law asked for a plaque for his SGT, which was being promoted to LT.
The base plaque is Red Oak with Cherry Stain
The badge is Maple painted Gold
Badge is inlayed into the base....

Scott
thank you for the info
I have grounded my DC with braided copper wire on all the PVC Pipe used in the final runs etc
and grounded that to the Cyclone
so one issue is out of the running...

Thanks
They say it may be poor grounding
Problem I will have is that I am legally blind Iraq Vet and have a great deal of problems doing weiring etc.
I sort of pisses me off to have this type of...

Ken
Thanks for the info, it is a DELTA VFD
It states fault correct hit reset
what fault?
switch being hit or spindle being stopped by material etc

Thanks for the response
Yes I ran the Zero process from the same location
I will double check to make sure there were no debrief etc
since I know the finishing cut is very small.
any ideas what...