Well....I'm pretty sure you might be right about that. Shopbot will send someone soon to help me out but I'm still tryin! Thanks for your reply!
Type: Posts; User: sevans
Well....I'm pretty sure you might be right about that. Shopbot will send someone soon to help me out but I'm still tryin! Thanks for your reply!
Hello, I am having troubles with the Lower Wheel Bearings on the YZ Car. For some reason, the one on the right engages, yet the one on the left will not stay engaged...no matter what I do. It...
Hello,
After some adjustments that required loosening the Gusset Bolts, I noticed one bolt spinning. It appears as though the T Nut is completely stripped out. Any advice on how to add a bolt...
Hey There, have a quick question for you... I noticed that there are 2 set screws on the insides of the Aluminum Blocks holding the Z Extrusion. Any idea what those are for?
[QUOTE=TomH,ShopBot;200642]Welp, I had it backwards, thanks for clearing it up :cool:
Bigger pinion not being snug is definitely more likely, I couldn't think of a scenario that the 12mm would be...
Sure, I'll send you the specs. But for the record, it's the original pinions that are a tighter fit (the Browning EN 6418. It is snug enough that it does not click back and forth when you wiggle...
Thanks for letting me know that. The shaft on my motor measures 12mm. The original opinions were a tight fit. The new ones can spin around on the shaft (without key) not so for...
Thank You for the info. Today I realized, and not 100% sure how I feel or anyone else will, that the pinion set I received is slightly bigger than the original. I practically have to hammer on the...
Just for the record......... this is the problem I'm having. Been cutting signs like this for years.... Super smooth. Now this and seems to be getting worse....
I just pulled an x motor just to check it out. Took off the pinion (WITH MUCH FORCE). I noticed after that where the set screw hits the shaft of the motor is just mutilated. The key also has so...
Yep. I have a spindle square like that. Always showing out in X Direction.
Got it. Consider it done. :)
I cant envision what you mean by bending it into a Z... You mean like this:
http://www.talkshopbot.com/forum/attachment.php?attachmentid=31355&stc=1
PERFECT!!!! Thank You so much
Absolutely!!! See picture. Let me know if you need to see more. :Dhttp://www.talkshopbot.com/forum/attachment.php?attachmentid=31353&stc=1
The Y Beam (or gantry) is not perpendicular to the table. It is cocked out a bit at the bottom and obviously what is keeping my spindle from being plumb... Is there a fix for this?
EXCELLENT! Thank You
You know what...I don't know what the problem is. I have lost sight of it at this point. I started down the "Mechanical Issue" road 2 weeks ago and still nothing. I have removed and replaced the...
HAHAHAHA...did I say that? I apologize...For some reason I keep calling the Z the X and so forth and so on. Not great for getting support. What I meant is that the V Rollers will never align with...
I definitely will send a pic when i get back to my shop. Shopbot told me that they would never line up just right. The blocks are securely in place. It appears that something would have to get...
i just can't even thank you enough for this information. I have been working at it for quite some time now and am getting so frustrated. It pains me that no matter what the left rollers will never...
Does anybody out there know how to adjust these? Everything I've found in manual and online is very vague. Many Thanks for reading!
:D
This same thing is happening to me. I have wondered if it is Aspire. However, I did open up an older version to test that and it made no difference. I have completely disassembled everything,...
That does make sense. It is jerky for sure. These letters are 1.5" or so in height. I used a 120 degree her saf bit and fed it at 1.2. Spindle 18000 rpm's. how slow can you feed? Or should I?
Are there physical indications of a worn collet? Something in particular I can do/see to tell if it is worn?