Search:

Type: Posts; User: brain

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    2,858

    Hey guys, I've never been to a camp before,...

    Hey guys,
    I've never been to a camp before, but would love to attend this one. Is there a fee to attend? Also do we need to bring our laptops with software or any other items or supplies?
    ...
  2. Replies
    4
    Views
    3,666

    Adrian, thanks for the suggestions, but I...

    Adrian,
    thanks for the suggestions, but I still am having no luck. the mysticthumbs shows a preview in the lower corner of the folder when you click the file, but not all ai. show a preview even...
  3. Replies
    4
    Views
    3,666

    eps converter/viewer

    hello everyone,
    i'm still new to this forum, so I apologize if this is an old topic. I am looking for a way to view eps,ai,dxf,etc. files as thumbnails, either as a viewer or converting, then...
  4. Replies
    1
    Views
    3,782

    can you deconstruct a ready made panel?

    hey everyone,

    i have a dumb question. if you were to purchase one of the ready made panels from vectorart3d such as this one ...
  5. Replies
    4
    Views
    4,311

    ok, i did change the file extension and was able...

    ok, i did change the file extension and was able to open it. it was just the outer rectangle(darn). i thought it might be the outlines of the deer,trees, mountains, etc.. i guess nothings free, but...
  6. Replies
    4
    Views
    4,311

    free eps from vectorart3d?

    i was browsing on vectorart's website and while looking at the 3d designs, they have a free eps design listed.

    http://www.vectorart3d.com/store/index.cfm?Fuseaction=Detail&ID=50660

    when i...
  7. Thread: 1/8th " collet

    by brain
    Replies
    9
    Views
    5,825

    Thanks brad, the router came with a 1/4 & 1/2"...

    Thanks brad, the router came with a 1/4 & 1/2" collets already. Is there any need to get this one as well?
    Brian
  8. Thread: 1/8th " collet

    by brain
    Replies
    9
    Views
    5,825

    THANK YOU BOTH FOR THE REPONSE. THE ONE FROM...

    THANK YOU BOTH FOR THE REPONSE. THE ONE FROM PRECISE BITS IS ALIITLE MORE ATTRACTIVE TO ME. BLACKHAWK: I ASSUME THIS IS WHAT I NEED

    PCPG-0429-8KIT Deluxe PC Collet Kit (contains 1/8in., PG...
  9. Thread: 1/8th " collet

    by brain
    Replies
    9
    Views
    5,825

    I JUST CAME ACROSS THIS, WOULD THIS WORK, IS IT...

    I JUST CAME ACROSS THIS, WOULD THIS WORK, IS IT RECOMENDED.
    http://www.leevalley.com/US/wood/page.aspx?p=30126&cat=1,46168,46241,46168,46180
  10. Thread: 1/8th " collet

    by brain
    Replies
    9
    Views
    5,825

    1/8th " collet

    hey everyone,

    i'm trying to find some small bits(ballnose, endmills, etc.) and after looking on here i found cuttingtoolsource.com. i would like to order a few bits, however, after talking to...
  11. Replies
    1
    Views
    2,283

    edp and flute count

    hey guys,

    i was looking around on the boards and seen a link to cuttingtoolsource.com. a few of you got some bits and seemed to like them, so i'll give them a shot also. i've only had my prs...
  12. wax?

    has anyone tried wax? like a block of parrifin? not sure how everyone else does it, but i always run them back through the planer or drum sander. what about soap? i imagine anything to seal off the...
  13. Replies
    6
    Views
    5,693

    thanks guys for the replies. lots of good info,...

    thanks guys for the replies. lots of good info, especially writing down the home coords. i played around with it today, to see what i could get away with. and it went to home everytime. thanks again...
  14. Replies
    6
    Views
    5,693

    keeping home position

    hello,

    i'd like to say hello to everyone. i'm new to this forum, and just got my prs4x8 this week. i've done a few test pieces to get used to it, but i do have a few questions. (i'm sure i'll...
Results 1 to 14 of 14