Search:

Type: Posts; User: coryatjohn

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    11
    Views
    272

    Well, I guess you should give SB a call and put...

    Well, I guess you should give SB a call and put in an order!
  2. Replies
    11
    Views
    272

    A horse was great for transportation until...

    A horse was great for transportation until something better was invented. Would you invest $65k in a device with a 20 year old control system?
  3. Replies
    11
    Views
    272

    But are they using the same old tired control...

    But are they using the same old tired control system that's so beyond obsolete as to not even be funny?
  4. Replies
    1
    Views
    57

    I'm not a sign guy but I've used this product...

    I'm not a sign guy but I've used this product successfully: Artool Ultra Mask Professional Masking Film

    It cuts easily and cleanly with the router.
    ...
  5. Replies
    11
    Views
    272

    Did they update the control system too or did...

    Did they update the control system too or did they keep the old one?

    Frankly, it doesn't look that enticing for twice what the old one cost.
  6. Replies
    4
    Views
    322

    I would think that anything laser would be too...

    I would think that anything laser would be too coarse for the OP's requirements.
  7. Replies
    4
    Views
    386

    With low temperature plastics like acrylic and...

    With low temperature plastics like acrylic and especially PVC, I find the best results are with an upcut single flute running low rpm's and a fast speed. The chips have to be cleanly ejected or they...
  8. Replies
    3
    Views
    641

    >> The first thing your friend needs to do it...

    >> The first thing your friend needs to do it contact the local township zoning/building department.

    An organization that I volunteered with asked if I could make a sign for them as they had...
  9. Melting plastic typically indicates the speeds...

    Melting plastic typically indicates the speeds are too slow and the RPM's are too high. Lower the RPM's to the minimum and increase the speed. The problem with small bits and plastic is the chips,...
  10. Thread: Aspire 11

    by coryatjohn
    Replies
    2
    Views
    657

    I'm afraid you cannot sell, transfer or give away...

    I'm afraid you cannot sell, transfer or give away your Aspire license. It's against their terms and conditions:

    https://www.vectric.com/terms

    4.3) The rights to the Software cannot be...
  11. Have you tried using a \n or \r character? It...

    Have you tried using a \n or \r character? It might work even if not documented.
  12. Replies
    10
    Views
    992

    As usual, Brady provides the actual procedure....

    As usual, Brady provides the actual procedure. Thanks!
  13. Replies
    10
    Views
    992

    It sounds like your machine was either screwed up...

    It sounds like your machine was either screwed up from day one or something happened to torque it. Did a semi crash through your shop lately?

    I believe you can adjust the squareness (which is...
  14. Replies
    10
    Views
    879

    I think the amount of pinion wear that's...

    I think the amount of pinion wear that's acceptable is up to the user. For me, I value accuracy and repeatability over unit cost so I change my pinions whenever they start to show slop. It took 7...
  15. Replies
    10
    Views
    879

    I suggest two things for the pinions: 1. Get a...

    I suggest two things for the pinions: 1. Get a allen socket to crank in some torque on those set screws. The angle wrenches just don't have enough oomph to do it. 2. Use Loctite.
  16. Replies
    10
    Views
    879

    I suggest refraining from hitting the red stop...

    I suggest refraining from hitting the red stop button during bit changes. It's not only unnecessary, it also cuts power to the motors, rendering them free to move. All you need to do is remove the...
  17. Replies
    10
    Views
    879

    I have a 2013 PRS Alpha and when the system is...

    I have a 2013 PRS Alpha and when the system is powered up, the gantry is solid as a rock. No way to move it at all. I've changed bits hundreds of times and never lost position.

    I suspect your...
  18. Replies
    3
    Views
    471

    If you don't call, you won't know. Besides, it...

    If you don't call, you won't know. Besides, it would probably cost more to ship the darn thing than buy it regardless of where you sourced it (unless Amazon Prime).
  19. Replies
    3
    Views
    471

    Have you tried calling Shopbot?

    Have you tried calling Shopbot?
  20. If you have similar motors on other axises, swap...

    If you have similar motors on other axises, swap them and see if the problem persists. If it moves to a different axis, then you likely have a failing motor. If it persists on the same axis, it's...
  21. Thread: Value Help

    by coryatjohn
    Replies
    3
    Views
    598

    No actual help in your case but what I did is...

    No actual help in your case but what I did is take pictures of the values screens and saved them in my photos. That way, when SB's software blows the settings files, I can easily refer to them on my...
  22. What do you mean by dormant? Was it operational...

    What do you mean by dormant? Was it operational when you stopped using it? If so, then it's very likely all you'll need to is clean off the cobwebs and fire it up. If you pulled it out of a flood, or...
  23. You should also specify if there's any warranty...

    You should also specify if there's any warranty and what software, if any, comes with the sale.

    Good luck with the sale! I hope you get asking price.
  24. Glad you got it sorted out.

    Glad you got it sorted out.
  25. Thread: Dash Panel

    by coryatjohn
    Replies
    2
    Views
    482

    How did you do the printing?

    How did you do the printing?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4