Search:

Type: Posts; User: uffabrew

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    14,833

    Rabbit Laser USA

    I purchased a Rabbit Laser USA (China import) model RL1290 80 watt 36x48" over three years ago and I am very pleased with it. I have students using it on every project for cutting, inlay work and...
  2. Free Guitar Patterns and Curriculum --- http://www.guitarbuilding.org/#!curriculum

    Any other schools using the patterns from http://www.guitarbuilding.org/#!curriculum? My students and I are cutting out bodies that we downloaded from them. They have five or six free ones to...
  3. Replies
    2
    Views
    2,017

    VFD will not power up

    Our ShopBot VFD will no longer power up. We last used it this Friday to cut out Guitar bodies, but today (Saturday) when I came in to cut out the guitar necks the VFD would not power/light up. I...
  4. Replies
    7
    Views
    2,557

    Resolution Multiples

    The problem was within the resolution multiples. They were set to 5,5,5,5,1. Reset them all to 1,1,1,1,1 and everything is working fine now.


    Thank you for the help. :)


    Best Regards,
    ...
  5. Replies
    7
    Views
    2,557

    It is an old PR ShopBot that we have upgrade to...

    It is an old PR ShopBot that we have upgrade to use the 4g control box. The XY jog speed is set to 6IPS while the move XY is at 4IPs.

    I can use the keyboard (K) an input values to have it move...
  6. Replies
    7
    Views
    2,557

    JOG distances bad, Move distances good

    Just finished reinstalling and upgrading to the most current version of the Shopbot software 3.6.16. I have set my unit values so that they are accurate. 1" move equals 1" of travel in X, Y and Z. ...
  7. Replies
    9
    Views
    2,646

    MY PC is an old AMD single core CPU 3000MHz ...

    MY PC is an old AMD single core CPU 3000MHz running XP. Only thing that bugs me about the control box to PC is the serial to usb converter. If it wasn't for that, I might attempt to run it on...
  8. Replies
    9
    Views
    2,646

    The 10200 Z unit value setting worked and it...

    The 10200 Z unit value setting worked and it appears to be extremely close if not dead on. I will do further testing later. My students are currently cutting out long-board skateboard decks. I...
  9. Replies
    9
    Views
    2,646

    PR upgraded to 4G -- z unit value help?

    I have an early 1990's PR ShopBot that we have upgraded to a 4G control board with the most current drivers (3.6.x) & firmware(1.4.0). It still uses the ball screw for the Z axis which is driven by...
  10. Replies
    25
    Views
    8,341

    I was lucky when I stumbled across that website ...

    I was lucky when I stumbled across that website after endless searches for an updated Jointer safety test. Thought it was worth sharing. I too, treat the Shopbot as an specialized router when it...
  11. Replies
    25
    Views
    8,341

    Great site for your safety tests and review...

    Great site for your safety tests and review sheets.

    http://cte.dpsk12.org/indtechsafetytests.html
  12. Replies
    5
    Views
    1,174

    I have had the same problems. The only way I got...

    I have had the same problems. The only way I got around the error was to record the line of code it stopped at. Then reboot the system and pick the Shopbot file from the next line. It is not a...
  13. Replies
    3
    Views
    873

    Lost communcations error

    The last three out of four .sbp files have generated a lost communications error. We are running the most current release of the control software for our ShopBot. Some part files work fine. ...
  14. Replies
    3
    Views
    1,174

    X & Y Gantry Upgrades

    Are there any X & Y rail + Gantry Upgrades from Shopbot? Or does one need to get look for a third party suppliers?

    I have an old Cable Drive system that was upgraded to a rack and pinion back...
Results 1 to 14 of 14