Search:

Type: Posts; User: drodda

Page 1 of 20 1 2 3 4

Search: Search took 0.28 seconds.

  1. Replies
    10
    Views
    4,695

    I got my code from Tony at Vectric this morning....

    I got my code from Tony at Vectric this morning. I really appreciate the fast service you get from these guys. They are like most of us it seems as he was working on Sunday too. Thanks Tony for the...
  2. Replies
    10
    Views
    4,695

    Thanks guys I have done all the suggestions, I ...

    Thanks guys I have done all the suggestions, I was just trying to jog my memory of how the code was delivered the first time by asking. I bought this long before shopbot was involved with Vectric...
  3. Replies
    10
    Views
    4,695

    I found the file I downloaded to get the program...

    I found the file I downloaded to get the program loaded back in 2006 but I can't find my user name and License code for it. Does anyone remember how that was given to us? By email or was it done...
  4. Replies
    10
    Views
    4,695

    PhotoVcarve Vectric Question

    Does anyone know how this program was delivered? I bought this back in 2006 and used it quite a bit. I have since replaced my computer and can no longer find the disk if I ever got one for this...
  5. Here is a picture of my first try at the Mother...

    Here is a picture of my first try at the Mother Of Pearl Inlays in maple.
    8008
  6. Went ahead and cut the Mother of Pearl with the...

    Went ahead and cut the Mother of Pearl with the Precisebit bit at 0.2/ips feed and 0.2/ips plunge adn it cut great. I used a piece of corian screwed to the table and double sided tape to hold the...
  7. I am using Partwizard for cutting and I can't...

    I am using Partwizard for cutting and I can't figure out how to ramp the bit in on a cut? ANyone familiar with partwizard and ramping?

    Thanks Chris for the tips.

    -D
  8. I have used the inlace a few times and had good...

    I have used the inlace a few times and had good results with it but never tried fine lines or anything. I already read that thread that you linked however they are talking feed rates above the...
  9. SLowest feed and plunge rates the shopbot software will work with

    Does anyone know what the smallest i.e. slowest the bot can got? I am trying to cut Mother Of pearl and the recomended rates of 7.5 IPM and 3 ipm are causing my bot to lose it's palce and it goes...
  10. Replies
    16
    Views
    6,196

    Chris, How many of these can you cut per...

    Chris,

    How many of these can you cut per bit? at $35 per bit I am trying to get an idea of cost per carving in slate?

    Has anyone used the bot to cut clear through slate and make a shape...
  11. Replies
    10
    Views
    4,047

    Well put Chuck!!! There is money to be made,...

    Well put Chuck!!! There is money to be made, people just need to adapt and change and get out of their comfort zone a bit to tap into the money. Think outside the box and try new things. If cabinets...
  12. Thread: Small bits

    by drodda
    Replies
    5
    Views
    2,375

    Precisebits.com have a great selection and fast...

    Precisebits.com have a great selection and fast shipping. Would not buy from anywhere else.

    -D
  13. Replies
    12
    Views
    7,483

    I only use the bits for a single project. I have...

    I only use the bits for a single project. I have a system that I use and I price the bits into my costs for the table projects so I use them and then put them in the box. I know there are tools in...
  14. Replies
    12
    Views
    7,483

    Jack, My thoughts are pretty much the same....

    Jack,

    My thoughts are pretty much the same. Is the smaller diameter worth the price difference? The end mills cost $12.50 new and I am not sure that even for $5.00 it is worth the hastle. I am...
  15. Replies
    12
    Views
    7,483

    Gerald, Thanks for the link, one question...

    Gerald,

    Thanks for the link, one question though, are the bits still .25 inch in daimeter once they are sharpened or do they lose a litle size?

    Thanks,

    Dave
  16. Replies
    12
    Views
    7,483

    Router bit sharpening question?

    Anyone on here know someone who does router bit sharpening? I have over 200 hundred 1/4" downspiral whiteside bits that need sharpening. I checked with a local guy and he wanted more than I am paying...
  17. Replies
    36
    Views
    27,087

    I just sanded and finished it like it was just a...

    I just sanded and finished it like it was just a plain piece of wood. The inlace sands like wood and then I stained and applied ocnversion varnish. YOu want to overfill the inlay and let dry. Then...
  18. Replies
    36
    Views
    27,087

    Here is what the Inlace ended up looking like. It...

    Here is what the Inlace ended up looking like. It worked out perfect for what I needed. No visible shrinkage but had to be careful with bubbles in the epoxy. The Inlace is the numbers and stars cut...
  19. http://www.custommadeboxes.com I use them...

    http://www.custommadeboxes.com

    I use them all the time. Super fast service and overall great people to work with. A small family owned company that exceeds my expectations on every order. Give...
  20. Thread: Pay Per Click

    by drodda
    Replies
    43
    Views
    15,490

    PPC is a scam at best. Unless your targeted...

    PPC is a scam at best. Unless your targeted market is nationwide you should just work on SEO for your keywords and your local town. You need a large budget to get any real use out of PPC advertising....
  21. Replies
    9
    Views
    4,637

    Tommy's chili cheese burgers are the bomb!!!! Not...

    Tommy's chili cheese burgers are the bomb!!!! Not the new franchise ones either the original is the only way to go.
  22. Thread: To Admin

    by drodda
    Replies
    5
    Views
    2,877

    If I had a dime for every time I have thought...

    If I had a dime for every time I have thought this? Most probably never ever find it hidden at the bottom like it is.

    Define soon? We have heard comments like this for quite some time and still...
  23. Replies
    28
    Views
    7,930

    Funny you should post this Danny. I have found...

    Funny you should post this Danny. I have found myself in the same frame of thought lately. I have been talking to the wife about this for the last few months. I have yet to pin point what it is, but...
  24. Thread: Concrete & Pine

    by drodda
    Replies
    27
    Views
    11,180

    Joe, Can you give a little detail about the...

    Joe,

    Can you give a little detail about the method you used to fix the dot of the second I in the word families? I was going to ask this earlier but though i would wait to see the finished sign...
  25. Replies
    34
    Views
    13,478

    5747 Another picture of just the sign

    5747

    Another picture of just the sign
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4