Search:

Type: Posts; User: Red F

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    345

    Not sure if it helps, but this is my tidbit of...

    Not sure if it helps, but this is my tidbit of knowledge on a similar topic.

    We have an older 16bit software system at work, and one problem I have had is the 64 bit computers will not run it. ...
  2. Thread: Forum Jibberish

    by Red F
    Replies
    4
    Views
    511

    I believe that is where the computer doesn't...

    I believe that is where the computer doesn't recognize quotation marks or something like that. Like this "
  3. Replies
    8
    Views
    591

    DWG is autocad. If there is a drafting teacher...

    DWG is autocad. If there is a drafting teacher at your high school, they may have software that could open it. Otherwise see if he has it saved as a DXF. Aspire can import those.
  4. Replies
    1
    Views
    295

    More CFM is more better.

    More CFM is more better.
  5. Thread: Hole not round

    by Red F
    Replies
    7
    Views
    953

    I found when I was running my router with a climb...

    I found when I was running my router with a climb cut on small holes at high feed rate, my holes looked like yours. I had a little slop in the machine like bill.young just talked about and the climb...
  6. Replies
    11
    Views
    1,484

    I'm sorry that I am no help answering your...

    I'm sorry that I am no help answering your question, but I am curious about your vacuum setup. I'm trying to work out some vacuum workholding form my machine and I wonder, are each of your pods...
  7. Replies
    5
    Views
    1,021

    Just from what I remember looking at the one I...

    Just from what I remember looking at the one I used to own. I believe that if you run your table too far back, it bumps into that bolt and kicks the stepper motor out a tiny bit so that it doesn't...
  8. Replies
    11
    Views
    1,537

    Thank you for the clarification Eric. I...

    Thank you for the clarification Eric. I appreciate it.
  9. Replies
    11
    Views
    1,537

    Thank you Eric for the recording of the Webinar. ...

    Thank you Eric for the recording of the Webinar.

    I played with the calculator a little bit and one thing I am a little confused on is the relationship between depth of cut and chipload. It is...
  10. Thread: Table legs

    by Red F
    Replies
    13
    Views
    1,902

    Reminds me of this old thread. ...

    Reminds me of this old thread. http://www.talkshopbot.com/forum/showthread.php?24604-White-oak-table

    He was building 4 sides for each leg and mitering them together
  11. Replies
    4
    Views
    1,341

    One possibility is that your bit isn't truly 120...

    One possibility is that your bit isn't truly 120 degrees or 90 degrees. That would cause over-cutting in the corners like you see on the body of the "I". You can test out cutting some sample...
  12. Thread: 4x8 prt standard

    by Red F
    Replies
    12
    Views
    4,895

    I'm guessing it is in Cookeville TN

    I'm guessing it is in Cookeville TN
  13. Thread: Is CNC cheating?

    by Red F
    Replies
    25
    Views
    7,339

    I know I'm kind of a smart ass, but I named my...

    I know I'm kind of a smart ass, but I named my router "Hand". Got around that "hand made" problem.
  14. Replies
    9
    Views
    2,480

    Eric, that model is great and I'm digging that...

    Eric, that model is great and I'm digging that table you have the model on. We are setting up a new to us non-blue CNC at work and I need to build an off-load table for it. I think I'll try to do...
  15. Replies
    14
    Views
    5,534

    It looks like the tool path is not set for a 60...

    It looks like the tool path is not set for a 60 degree bit, or your z is not zeroed correctly.
  16. Replies
    24
    Views
    6,212

    I bought a Makita track saw to save a little...

    I bought a Makita track saw to save a little money over the festool. The quality wasn't good enough for me, so I sent it back and bought the smaller Festool corded saw (TS55?). I couldn't be...
  17. Thread: Collet help

    by Red F
    Replies
    9
    Views
    2,003

    precise bits has a 1/8" collet and nut for some...

    precise bits has a 1/8" collet and nut for some router models.

    https://www.precisebits.com/gateways/ColletsNutsHome.htm
  18. Replies
    9
    Views
    3,627

    Appears to be a standard. There is red on the z...

    Appears to be a standard. There is red on the z axis motor
  19. Replies
    27
    Views
    9,176

    http://www.talkshopbot.com/forum/showthread.php?19...

    http://www.talkshopbot.com/forum/showthread.php?19903-Buddy-BT48-Alpha-table-MKIII&highlight=buddy+table

    Check out this thread. This is a great aluminum vacuum table built on a Buddy.

    Truely...
  20. Replies
    16
    Views
    4,865

    Brady, I’m trying to picture how a dial indicator...

    Brady, I’m trying to picture how a dial indicator can be used to true up the z-axis without something to offset it like the aforementioned shiny object.
    Would you mount it to the table and chuck a...
  21. Replies
    4
    Views
    2,624

    This has been sold and driven halfway across the...

    This has been sold and driven halfway across the country
  22. Replies
    23
    Views
    6,868

    It may be your surfacing pass and not your second...

    It may be your surfacing pass and not your second cut.

    Could a dull surfacing bit cause push itself up as it cut, or push the table material down?

    When I'm problem solving, I try not to take...
  23. Replies
    4
    Views
    2,624

    Sale pending.

    Sale pending.
  24. Thread: IBILD.com

    by Red F
    Replies
    21
    Views
    16,573

    That is a constant battle for our website guy at...

    That is a constant battle for our website guy at work. I happily only know a little about it.
  25. Thread: IBILD.com

    by Red F
    Replies
    21
    Views
    16,573

    I looked at the site on an Iphone SE. Some of...

    I looked at the site on an Iphone SE. Some of the section title words have to go onto multiple lines due to their font size and length. Also the animated typing bit at the end causes the FAQ part...
Results 1 to 25 of 98
Page 1 of 4 1 2 3 4