Search:

Type: Posts; User: kra

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    9
    Views
    11,743

    Still available Price lowered to $400 cash

    Still available
    Price lowered to $400 cash
  2. Replies
    9
    Views
    11,743

    Price lowered to $400 cash

    Price lowered to $400 cash
  3. Replies
    9
    Views
    11,743

    palatalizing is not a problem, but no way to get...

    palatalizing is not a problem, but no way to get around shipping cost
  4. Replies
    9
    Views
    11,743

    yes it is pretty heavy. would have to be motor...

    yes
    it is pretty heavy. would have to be motor freight
  5. Replies
    9
    Views
    11,743

    this is still available. will sell for $500 if...

    this is still available. will sell for $500 if anyone is interested
  6. Replies
    9
    Views
    11,743

    Spencer Vortex Regenerative Blower / vacuum

    Spencer Vortex Regenerative Blower / vacuum
    model# VB-055 (current model, accessories and parts readily available)
    perfect for a vacuum hold down top on your cnc router
    7.5 HP 3 phase TEFC motor...
  7. this item is sold

    this item is sold
  8. couldn't figure out how to edit my post but price...

    couldn't figure out how to edit my post but price is $5400
  9. Shopbot PRT 4'x8' standard 4g controller for sale

    PRT standard
    4g controller
    4' x 8' bed
    current software and firmware
    windows 7 pro 64 bit computer (fresh install)
    good condition
    (no spoil board currently installed. Getting ready to install...
  10. Replies
    8
    Views
    17,274

    pm sent thanks

    pm sent
    thanks
  11. Replies
    8
    Views
    17,274

    does it have the red drivers or the black ones?...

    does it have the red drivers or the black ones?
    pic?
    would you consider $400?
  12. Replies
    8
    Views
    17,274

    interested in the 4g if it is still available...

    interested in the 4g if it is still available
    thanks
  13. SOLD thanks

    SOLD
    thanks
  14. Sold

    SOLD
    thanks
  15. sale pending

    sale pending
  16. and a few more pics

    and a few more pics
  17. more pics

    here are a few more pics
  18. PRT Alpha 4x8 w/ Colombo 4 hp spindle, Yaskawa V1000 spindle drive, 4 zone vac table

    PRT Alpha 4x8
    Colombo 4 hp spindle with Yaskawa V1000 drive running single phase
    spindle recently serviced with new bearings, etc. (just a few hours run time since serviced)
    4 zone vac table...
  19. here is a link to all manuals, etc....

    here is a link to all manuals, etc.
    http://www.parkermotion.com/manuals/S-SX/S-SX.htm
  20. another pic of model #

    another pic of model #
  21. Parker/Compumotor microstep drives for sale SX8 S series

    I have 5 Parker/Compumotor SX8 microstep drives for sale
    I was told they were all in working condition but 2 of them needed fuses (these 2 are marked). they have internal fuses that fit in fuse...
  22. Replies
    10
    Views
    7,811

    probably obvious but i also start cut from side...

    probably obvious but i also start cut from side and move into part keeping z the same throughout cut and park spindle out of the way for loading next part always keeping z the same (in my case 0 )...
  23. Replies
    10
    Views
    7,811

    wayne i cut approx 1/16" oversize and let the...

    wayne
    i cut approx 1/16" oversize and let the edge profile bit clean it up to exact size
    my jig is just lightweight mdf with vac pulling strait thru from normal vac table
    no special gaskets or...
  24. Replies
    10
    Views
    7,811

    wayne, i cut a similar edge profile but much...

    wayne,
    i cut a similar edge profile but much thinner material on a regular basis using a raised jig just made slightly smaller than piece being cut (actually larger than piece being cut but a trough...
  25. Replies
    9
    Views
    10,344

    also make sure your bit is not painted on the...

    also make sure your bit is not painted on the bottom keeping it from making contact
    I use a bit from one company and they are always painted and I have to sand off the paint to z-zero
Results 1 to 25 of 44
Page 1 of 2 1 2