Search:

Type: Posts; User: tlempicke

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. shopbot upgrade

    I have my Buddy 48 inch machine converted to the Centroid system. Much easier to run, works first time every time. It is also quite a bit more accurate and faster. It is going to cost quite a bit...
  2. Thread: Desktop 2012

    by tlempicke
    Replies
    6
    Views
    839

    If that is all the effort you are willing to put...

    If that is all the effort you are willing to put into the sale of it why should we be interested?
  3. Replies
    4
    Views
    450

    With a VFD it is possible to have just about any...

    With a VFD it is possible to have just about any voltage and frequency for both the input and the output. Since you bought it from Amazon I certainly would not experiment with it. Amazon is good...
  4. Replies
    8
    Views
    858

    I know this is not directly related but I have...

    I know this is not directly related but I have the control board that goes in the VFD for sale at $125. Complete with wiring and shielded USB cable. Costs $250 new from Shopbot.
  5. Thread: PRSstandard

    by tlempicke
    Replies
    18
    Views
    3,355

    The results you are getting here seem to be...

    The results you are getting here seem to be directly related to the amount of effort you are willing to put forth.
  6. Replies
    23
    Views
    2,538

    I thought that I had put these on the forum but...

    I thought that I had put these on the forum but now I can not find them.
    I have two steppers from my buddy for sale. They are $125 each plus shipping. Will go in a large USPS one rate box I...
  7. Back in 2017 I made an indexer for my buddy from...

    Back in 2017 I made an indexer for my buddy from a cheapy that I found on E Bay. Works great and I have made a few things on it. Not all that big a deal. I extended the Z axis by 3 inches by...
  8. Thread: FABMO Status

    by tlempicke
    Replies
    26
    Views
    3,934

    WHAT??? Your just in your Salad days. I am 80...

    WHAT??? Your just in your Salad days. I am 80 and I was able to pick up the new software with no problem at all. I built my own setup and by the time I was finished I pretty much knew just what I...
  9. Thread: FABMO Status

    by tlempicke
    Replies
    26
    Views
    3,934

    Tom First of all look at the date I joined...

    Tom

    First of all look at the date I joined this forum. I currently own two shopbots, my fourth and fifth. I say this to let you know that I am a long time and truly committed fan.

    I refer you...
  10. Thread: FABMO Status

    by tlempicke
    Replies
    26
    Views
    3,934

    The Oriental Motors are getting to be old...

    The Oriental Motors are getting to be old technology. Newer motors that provide a whole lot more OOmph in the same size package make the machine faster and more accurate. If you look at the pix...
  11. Thread: FABMO Status

    by tlempicke
    Replies
    26
    Views
    3,934

    Gerald My first shopbot was in the 1990's and I...

    Gerald
    My first shopbot was in the 1990's and I am now on my fourth. I decided last Fall to upgrade the electronics. I am just ready to make chips and it appears that this is going to be a great...
  12. Replies
    3
    Views
    690

    Forgot we had that. Thanks

    Forgot we had that. Thanks
  13. Replies
    0
    Views
    394

    Spindle controller for Yaskawa drive

    This is a spindle controller that was purchased from Shopbot and is functionally identical to the newer one on sale for $250. Come with wiring harness and cable to connect to your computer.
    ...
  14. Replies
    3
    Views
    690

    Bump this message

    Bump this message
  15. Replies
    3
    Views
    690

    Spindle controller for Yaskawa V1000

    This is a spindle controller that was purchased from Shopbot and is functionally identical to the newer one on sale for $250. Come with wiring harness and cable to connect to your computer.

    $125...
  16. Replies
    1
    Views
    462

    Any interest at all out there?

    Any interest at all out there?
  17. Replies
    4
    Views
    833

    Shopbot can freely give their software away...

    Shopbot can freely give their software away because it is written to work with the Shopbot control board. So No.
  18. Replies
    1
    Views
    462

    SB motors for sale - from 48" Buddy

    I have three Shopbot motors for sale. These are from a 2008 Buddy and have seen only hobby use. All in perfect working condition. $150 each plus shipping....
  19. The box is sold

    The box is sold
  20. My email is tom@lempicke.com

    My email is
    tom@lempicke.com
  21. Replies
    5
    Views
    913

    Shopbot has them for sale at their site and also...

    Shopbot has them for sale at their site and also has the softwear for download. It is a really nice thing to have. As the computer starts up it is logged in as if it was a second keyboard. There...
  22. Shopbot Control box 4th gen for sale complete

    This is a Gen 4 control box that I have been using for the past few years. It is quite reliable and never has had many of the USB problems that you see here on the web. It is complete with three...
  23. Replies
    5
    Views
    913

    Shopbot Pendant

    Here is a picture of the pendant
  24. Replies
    5
    Views
    913

    Shopbot pendant FS

    I have a Shopbot USB pendant for sale. Excellent condition works perfectly.
    $75 includes shipping in the US.
  25. Replies
    8
    Views
    1,752

    It is probably a DC fan and so the extra wire is...

    It is probably a DC fan and so the extra wire is most likely a ground wire. Use an ohm meter and you can probably figure out what is what pretty quick. The pos and neg will have a resistance as...
Results 1 to 25 of 476
Page 1 of 20 1 2 3 4