Search:

Type: Posts; User: Tom Bachman

Page 1 of 13 1 2 3 4

Search: Search took 3.34 seconds.

  1. Replies
    2
    Views
    912

    Sent email to Tech Support and we got it figured...

    Sent email to Tech Support and we got it figured out this afternoon. After testing we have deduced that the X2 motor is lagging and needs replaced. I'm in the process of finding a suitable...
  2. Replies
    2
    Views
    912

    PRT 9648 issue

    Hey guys been away for a while. Been communicating on the FB page some, but not getting much help recently.

    Got an issue where the machine seems to lose the x location. It actually jumped off...
  3. Replies
    3
    Views
    1,318

    Yea, no love there. and I looked back to the last...

    Yea, no love there. and I looked back to the last time this happened, and tried the solution, still no love.

    Any other suggestions?
  4. Replies
    3
    Views
    1,318

    Thanks Sxott, I'll give it a try.

    Thanks Sxott, I'll give it a try.
  5. Replies
    3
    Views
    1,318

    Input 4 error

    Hey guys, I was doing an engraving cut with my PRT STD, I hit the space bar to stop the file and the machine acted funny, like it was thinking about the command, then it poops up with the Limit...
  6. Replies
    2
    Views
    1,046

    Your location might help in finding interested...

    Your location might help in finding interested parties.
  7. Replies
    3
    Views
    1,339

    Just a quick search came up with this ...

    Just a quick search came up with this

    https://suncatcherstudio.com/patterns/us-states/
  8. Add some pictures and your location.

    Add some pictures and your location.
  9. Hey Ray. This is just like the one I started with...

    Hey Ray. This is just like the one I started with when I was teaching. They still use it daily at the school. 7 years ago I bought that one for $6500. I see them advertised for anywhere from $3500...
  10. Replies
    5
    Views
    4,228

    Cool models!

    Cool models!
  11. Replies
    9
    Views
    2,385

    Had a bit fly out of a hand-held router once....

    Had a bit fly out of a hand-held router once. Looked all over for it, no idea where it went. About a half hour later, one of the other students headed back to the bathroom and found it...more than 60...
  12. Replies
    8
    Views
    5,012

    I'll check on that tomorrow, Scott, Thanks again.

    I'll check on that tomorrow, Scott, Thanks again.
  13. Replies
    8
    Views
    5,012

    Thanks Jerry!

    Thanks Jerry!
  14. Replies
    8
    Views
    5,012

    Are firmware updates available on the SB site?...

    Are firmware updates available on the SB site? not sure I've ever looked.

    Yea, I had to change the Unit values for my Z axis due to the motor and pinon I have on it. I'll have to find where to...
  15. Replies
    8
    Views
    5,012

    Scott, you are correct! That's what it...

    Scott, you are correct! That's what it was...didn't remember that being an option, but found the place to switch to full and it is working. Also the machine is back to working properly....

    Thank...
  16. Replies
    8
    Views
    5,012

    Problem with Control Software

    OK, long story shortened.....

    Turned on the bot this morning, started the control software, error on start up Some variable message....Thinking is was an issue with the control software (we had a...
  17. To bad you're not closer, I'd be interested in...

    To bad you're not closer, I'd be interested in looking at this machine. Good luck with the sale.
  18. Replies
    6
    Views
    5,157

    Ok, I think I got it. The Value for z with my...

    Ok, I think I got it. The Value for z with my pinion should be 509.2956.
  19. Replies
    6
    Views
    5,157

    Ok, from the FB users page one suggestion was; ...

    Ok, from the FB users page one suggestion was;

    This solution worked...except I had to re-install the control software (well didn't have to, but thought it prudent to do so)

    Now the only thing...
  20. Replies
    6
    Views
    5,157

    Didn't get rid of the machine, just worked went...

    Didn't get rid of the machine, just worked went back to the original board and got it going. Then last year (almost exactly one year) the control board shot craps completely and more or less forced...
  21. Replies
    6
    Views
    5,157

    Machine flaky ..... 2020 ?

    I used my PRT standard Monday, everything worked just fine. When I was done and shut the shop down for the day, I turned the control box off. This morning I went to cut a file and I started the...
  22. Replies
    5
    Views
    6,284

    Hey everyone....Rob is a first rate guy. I bought...

    Hey everyone....Rob is a first rate guy. I bought the 7519 from him for a good price...and he sent pictures that really didn't show what I was really getting..... the router motor, in real life, was...
  23. Replies
    8
    Views
    9,426

    Well, a new V4g control board fixed the problem....

    Well, a new V4g control board fixed the problem. Not a cheap fix, but one I had contemplated over the years about doing anyway. I know they said the new board wouldn't make the machine faster, but...
  24. Replies
    1
    Views
    1,532

    Ordered a new V4g board from Shopbot

    Ordered a new V4g board from Shopbot
  25. Well, it wasn't the computer They have determined...

    Well, it wasn't the computer They have determined that a V4g upgrade should fix my problem, so I just ordered that from Shopbot. Thank you for your help.
Results 1 to 25 of 317
Page 1 of 13 1 2 3 4