Search:

Type: Posts; User: cradke0419

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    192

    Hold down for planing slabs

    I am trying to make a hold down for planing slabs. I bought some unistrut to act as a t track. Planning on bolting that down on the bed and using wedges to keep the slab tight. Also thought of...
  2. Replies
    4
    Views
    785

    I contacted thermwood and they emailed me the link

    I contacted thermwood and they emailed me the link
  3. Replies
    4
    Views
    785

    thanks for the quick reply I have been looking...

    thanks for the quick reply I have been looking and reading forums but everyone I click on and look at leads to a dead end with a 404 error page
  4. Replies
    4
    Views
    785

    shopbot link

    Where do I download the shopbot link? I purchased the dongle a few years back and bought a new computer but cant seem to find where to download it from. Sorry for the elementary question
  5. Replies
    16
    Views
    1,817

    I will have to try that torch trick. Thanks

    I will have to try that torch trick. Thanks
  6. Replies
    16
    Views
    1,817

    Thanks guys. Yeah I am going to have to break...

    Thanks guys. Yeah I am going to have to break those edges. They have a few sharp spots. Is it OK to run the vacuum hold down for extended periods of time?
  7. Replies
    16
    Views
    1,817

    33761 I don't know why I didn't think of this...

    33761
    I don't know why I didn't think of this earlier but this tool is awesome for cutting tabs. Too bad I figured that out on the last sheet!
  8. Replies
    16
    Views
    1,817

    33760 Need to make 18 of these things by...

    33760
    Need to make 18 of these things by Monday. Donating my time for this project but hope it helps. Don't know what to think about the one time use and probably never used again but I guess...
  9. Replies
    16
    Views
    1,817

    33759 I haven't cut plexiglass before but those...

    33759
    I haven't cut plexiglass before but those edges are as smooth as can be. Very happy with the results. They are just a barrier between the poll workers and the voters sitting on a table. ...
  10. Replies
    16
    Views
    1,817

    First one done. What do you guys think...

    First one done. What do you guys think
    ATTACH=CONFIG]33757[/ATTACH]
  11. Replies
    16
    Views
    1,817

    Was thinking about making it more eye pleasing...

    Was thinking about making it more eye pleasing than 2x material. Thought about something like this. 33755
  12. Replies
    16
    Views
    1,817

    3375433754

    3375433754
  13. Replies
    16
    Views
    1,817

    Plexiglass dividers for voting booth

    Need to make some plexiglass dividers for voting booths. I have 4x8 sheets 1/8" thick. Was going to cut them in 3rds and make them 48x32 approximately. Need to build a base so they can stand up on...
  14. I just cut out about 20 sheets of plywood for...

    I just cut out about 20 sheets of plywood for cabinet parts using ecabinets and the spindle shutoff each time like it should. Used vcarve and it would not shutdown
  15. Colombo spindle with delta vfd not shutting off after cut

    I have issues with the spindles shutting off after it is done cutting a file. I have 2 Colombo spindles with delta vfds. I pushed the mode button on the spindle and it goes to a different number...
  16. Want to make a topographic map of my area

    Hello I am looking to try making a topographic map of my area. I am not very good with vcarve pro yet but I'd like to try. Any suggestions on how to get started and what material to use. I am...
  17. Replies
    10
    Views
    7,970

    Thanks for all the replies and help so far. I do...

    Thanks for all the replies and help so far. I do appreciate it
  18. Replies
    10
    Views
    7,970

    I have since changed my dadoes to be .035 to make...

    I have since changed my dadoes to be .035 to make them fit good. Looking at the fit I know something isn't right because there is not 1/32" of slop in the joint. I set my plywood to .48 and my...
  19. Replies
    10
    Views
    2,472

    Right now I'm setup to zero off top of material. ...

    Right now I'm setup to zero off top of material. I am wondering how to change that to go off the bed so I don't have to rezero when I change material thickness. Does it have something to do with...
  20. Replies
    10
    Views
    2,472

    Thanks that helps to see what other people do. I...

    Thanks that helps to see what other people do. I use a 3/8" bit for outline and dadoes in the z axis and have a 5mm in the a axis.
  21. Replies
    10
    Views
    7,970

    I changed some settings and now it's much better....

    I changed some settings and now it's much better. It was set to .01 and I changed them to .025 and it's good. Thanks again for your help
  22. Replies
    10
    Views
    7,970

    Thanks a lot for your help I will mess with it...

    Thanks a lot for your help I will mess with it tonight.
  23. Replies
    10
    Views
    7,970

    Dadoes are too tight

    My dadoes are too tight was wondering where to change the tolerance. Thanks
  24. Replies
    10
    Views
    2,472

    Sounds good thanks Tim

    Sounds good thanks Tim
  25. Replies
    0
    Views
    632

    Z axis doesn't turn off after cutting

    I have a Colombo spindle 2.2 hp with a Delta vfd. The spindle doesn't shut off after cutting with it. It kinda slows down but very minimal. The a axis does turn off after cutting. Any ideas. ...
Results 1 to 25 of 44
Page 1 of 2 1 2