I have been trying different settings in link. I have found the tabbing problem, when cutting small parts, which I used to not have is now present as long as I try 2 tabs per part. If I go with a...
Type: Posts; User: loriny
I have been trying different settings in link. I have found the tabbing problem, when cutting small parts, which I used to not have is now present as long as I try 2 tabs per part. If I go with a...
I occasionally have run into this on cabinet backs where it seems the outline cut comes in by the width of my bit and cuts all sides an additional 5mm making the part 3/8" to small. The dadoes are...
Looks like spindles too high. Can the plate be lowered to a different set of holes on the Z carriage. I've got a Chinese spindle with a custom built mount plate so I don't know if your plate is...
Has the tabbing issue been resolved? I had to do a fresh install of ecabs on a new laptop with windows 10. It was tabbing like Don's photo. Now I managed to resurrect my old IBM think pad with xp,...
I was able to salvage the custom files Gary Campbell provided me with years ago and transferred them. Now its just like it was before, zeroing to the spoil board.
Thanks for the help.
Thanks.
Now the only other thing I can't seem to figure out now is zeroing to the table rather than the materials. I ended up having to setup a new control computer and not sure if these will work...
I've just had a computer crash and can't locate any of my backup files. I've downloaded the link again and am just not able to remember how to get my custom 95 to run at the end of each sheet to park...
I'm impressed to see that a bit of ingenuity and hard work can keep manufacturing at home. Its sad to see everything come from overseas. Keep up the good work.
Lorin
For a few years now I've only used titebond 3. Freezing it doesn't seem to hurt it. Costs more but when my boiler gives trouble I still have it to use. I've never had stain go bad from freezing...
Aspire is my easy money. Radius architraves and other odd ball things nobody else does can pay well when you can design quickly with the software and cut while building cabinets.
I was lucky and...
I don't want to argue with Don but I use tabs on all my smaller part. I think I'm set for anything under 5" wide. I'd be lost without them as I just run a 2 central vac hold down. I just touch the...
Ive got an older laptop for mine. I've been running the link for a few years and always have closed my SB3 control before sending the file. I just assumed this is normal and havent had an issue....
I've had very limited success doing it with full sheets. I only run 2 vac motors though. if i would get the better side to have the crown oi the middle it works with 2 passes. (climb cut, then...
All my banding is finished. I simply stack the whole job, spray or spray and wipe the stain and finish. Then before too long (within a day or 2) I scrub the little bit that got between the sheets....
With my HVLp I've thinned the clawlock up to 30%. It works but builds slow. Getting it sprayed with a good airless @ 100% does a beautiful job. Most of m MDF is done with Target pigmented water...
Very nice Gary. Another happy customer I'll presume
Lorin
I am in my 30's but not nearly so computer savvy as these "old" guys who keep helping me out. With any luck when I get near their age I too will be able to do the things with my router they do. As to...
Wow. I'm used to things taking forever to get into Canada but if I remember right it was here a week or so after ordering. I did set it up over the phone with special shipping instructions though.-...
Thats beautiful Kevin. Makes a guy wish for more time and patience to learn the indexer.
Lorin
I would do a real close look at the connectors.
Lorin
I second Targets products. I never set up to spray solvents and have almost exclusively used Target. Their finish is excellent and they have a forum that has been very good.
Good job on the shelf....
I think I overlooked the obvious. I had been envisioning a table saw if I feed the board rather than sliding the saw. Does this sound right. Build a 32 ft straight fence into a bench with my...
Nice work Kevin.
Ecabs can I'm sure give you a rendering like your finished product. I haven't gotten into that kind of detail and that has worked for me and my customers. Some of the stuff...
you're probably right Gary. I'm just now over doubling my shop size and also just bought another moulder. I'm hoping to pinch a few pennies but I might just look around.
Lorin
I'm trying to come up with an idea for a homebuilt straight line ripsaw to complement my moulders. Most of my material I can buy straight lined but not all. I have been using 16 feet of saw guide...