Search:

Type: Posts; User: pappybaynes

Page 1 of 14 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    591

    Oramask 813

    Oramask 813
  2. Replies
    4
    Views
    1,389

    On PVC I use a "0" flute at low RPMS and cutting...

    On PVC I use a "0" flute at low RPMS and cutting aggressively.
  3. Replies
    9
    Views
    3,310

    I did a separate motor for each quadrant - Eric...

    I did a separate motor for each quadrant - Eric bought my machine.
  4. Replies
    12
    Views
    3,418

    As usual Scott, AWESOME work!!

    As usual Scott, AWESOME work!!
  5. Replies
    17
    Views
    5,038

    So sorry to hear...I had asked him several...

    So sorry to hear...I had asked him several questions back in 2008-09 when I was getting started...I chuckle now, but at the time thought I was dealing with one of my old drill sgts!! But his advice...
  6. I cut my teeth on a Shopbot machine...going to an...

    I cut my teeth on a Shopbot machine...going to an event at headquarters in 2007. I purchased a 48x96 PRT in 2008 and used it part-time for years. I decided to go to a smaller unit as I was using...
  7. Replies
    16
    Views
    4,306

    Pretty sure I can put a check mark after all of...

    Pretty sure I can put a check mark after all of the above...if I could only remember when my pencil was...
  8. Replies
    20
    Views
    8,045

    Eric, is that the machine you bought from me??

    Eric, is that the machine you bought from me??
  9. Replies
    9
    Views
    5,078

    I have done 50+ "PVC" historical signs with...

    I have done 50+ "PVC" historical signs with Oramask...works great!http://www.talkshopbot.com/forum/attachment.php?attachmentid=26562&stc=1
  10. Replies
    15
    Views
    10,910

    I used the Onsrud 30 degree bit for my full table...

    I used the Onsrud 30 degree bit for my full table (4x8) gasket to cut cut 248 coasters...worked great!
    Dick
  11. Replies
    28
    Views
    13,855

    Glad you clarified Scott!!

    Glad you clarified Scott!!
  12. love to see you business card...

    love to see you business card...
  13. Replies
    28
    Views
    13,855

    Prayers for sure Scott, had back surgery, shots,...

    Prayers for sure Scott, had back surgery, shots, in pain for over 40 years, but nothing like you're going through - we pray for expert skill of the surgeon, strong screws and rods and speeding...
  14. Replies
    16
    Views
    12,132

    Sweet Scott! I still haven't used the micro...

    Sweet Scott! I still haven't used the micro bits...can't wait to start! BTW first job I got after I sold the big machine was too big for the small machine!!! Thank goodness there's an Alpha 5...
  15. Replies
    8
    Views
    4,822

    Thank you for the suggestions. Dick

    Thank you for the suggestions.
    Dick
  16. Replies
    9
    Views
    5,729

    Thank you all for your input!!

    Thank you all for your input!!
  17. Replies
    8
    Views
    4,822

    Exterior Clear Finish

    I am currently working on a large 2-sided sign made out of Port Orford Cedar - the letteres will be V-Carved and painted - normally I would use a spar varnish over the entire sign when...
  18. Replies
    9
    Views
    5,729

    Epoxy or ??? Tinted Wood Filler

    I am looking for something I can use to fill a V-carved design that is tinted - I want to be able to sand it flush with the piece. This a design carved in beer flight paddles...Any suggestions? ...
  19. Replies
    6
    Views
    4,537

    Do it Scott! Paul's a wealth of knowledge.. Dick

    Do it Scott! Paul's a wealth of knowledge..
    Dick
  20. Replies
    13
    Views
    9,000

    Probably just the nature of that piece of wood...

    Probably just the nature of that piece of wood...
  21. Replies
    13
    Views
    9,000

    Mahogany needs a lot of sealer as it is...

    Mahogany needs a lot of sealer as it is porous...I've used Spanish Cedar (actually in the Mahogany family) and Mahogany for exterior signs... great to carve, resistant to rot and bugs...just need to...
  22. Replies
    49
    Views
    26,701

    For a $1000.00 it's not only high tech but high...

    For a $1000.00 it's not only high tech but high priced!
    Dick
  23. Scott, if you go the Amana route the small one...

    Scott, if you go the Amana route the small one like I have is just fine is just fine...I used it on the big ShopBot and now on the smaller machine...cutters are easily and accurately replaced
    Dick
  24. Zamm, I use the smaller Amana RC 2249...

    Zamm, I use the smaller Amana RC 2249 http://tools.toolstoday.com/search?w=planing%20bits and love it. Dick
  25. Replies
    16
    Views
    11,125

    Joe, do you a Sikkens clear coat on your signs? ...

    Joe, do you a Sikkens clear coat on your signs? And if so which one?? Thanks
    Dick
Results 1 to 25 of 341
Page 1 of 14 1 2 3 4