Search:

Type: Posts; User: ssflyer

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    227

    OK, found and downloaded the original parameter...

    OK, found and downloaded the original parameter setup, and got it working...
  2. Replies
    6
    Views
    499

    He means turn off the ShopBot control "Easy"...

    He means turn off the ShopBot control "Easy" mode. Click the question mark (?) and select, "Switch to FULL"
  3. Replies
    1
    Views
    227

    Yaskawa V74x VFD displays 00 RPM

    Hi all,

    Yesterday my spindle wouldn't start. I checked the VFD; the run light was flashing and the RPM displays "00".

    The fan runs on the spindle, but that's a different circuit. I checked...
  4. Replies
    7
    Views
    1,252

    Hi Brady, I noticed that, too. A roughing pass...

    Hi Brady,

    I noticed that, too. A roughing pass was run, but the material was either slightly under 1.75" thick or I forgot to center the model in the material, which left a slight flat on it. As...
  5. Replies
    7
    Views
    1,252

    Interesting Flip-op sub-project

    Had to duplicate these round moldings for a 150 year old house. careful alignment is crucial when flipping for the bottom side cuts!
  6. Replies
    5
    Views
    2,173

    OK, got it figured out. I forgot that the 3/4"...

    OK, got it figured out. I forgot that the 3/4" generic material has grain specified. I had to set the grain direction in the link to match the material specified in eCabs.

    Hope this helps someone...
  7. Replies
    5
    Views
    2,173

    Hi Keith, Thanks for the reply. You have to...

    Hi Keith,

    Thanks for the reply. You have to select the material, and I only have one, so it has to match the part. I tried a way oversized piece, and still had the problem. The table parameters...
  8. Replies
    5
    Views
    2,173

    Thanks for the reply, Terry. That's exactly...

    Thanks for the reply, Terry.

    That's exactly what I do, but it still nests on a full sheet. I check the rectaglular checkbox, enter the dimensions, and it shows up in the, "add Sheet(s) dialog -...
  9. Replies
    5
    Views
    2,173

    Add Sheet(s) - ShopBot Link

    I seem to be missing something obvious. When I add a sheet to a ShopBot Link job, how do I get it to actually use it? I need to cut a single cabinet part on a smaller sheet, but after adding the...
  10. Replies
    2
    Views
    901

    Hi Jerry, It's home built, Windows 7 Ultimate 4...

    Hi Jerry,
    It's home built, Windows 7 Ultimate 4 core Intel processor. I think I have it fixed. I uninstalled the USB driver, updated the SB# software to 3.8.42, and re-installed the driver. Seems to...
  11. Replies
    2
    Views
    901

    BSOD on Shutown

    Hi all,

    New issue with the new computer: BSOD on computer shutdown caused by the CP2101 USB to UART bridge controller, installed by the ShopBot software. Has anyone experienced this, before? Never...
  12. Replies
    7
    Views
    1,885

    OK, found the issue! I just switched my old...

    OK, found the issue! I just switched my old design computer (Win 7 Ultimate 64bit), to use as my control computer. The playback configuration was still set to 5.1 surround sound, and I only hooked up...
  13. Replies
    7
    Views
    1,885

    Thanks guys, I tried a few other thing things:...

    Thanks guys,

    I tried a few other thing things: Changed the encoding, changed sound card settings, same result. The file plays just fine in VLC Player and Adobe Audition, just not with Windows...
  14. Replies
    7
    Views
    1,885

    Thanks Gary! The duration is set to 2 seconds,...

    Thanks Gary!

    The duration is set to 2 seconds, and the sound7 wave file exists. Interestingly, it plays fine in adobe audition, but is silent with windows media player. Missing codec or corrupt...
  15. Replies
    7
    Views
    1,885

    SB3 sound output

    I installed a new control computer, and updated the settings from a backup. Everything seems to weok just fine, except there is no sound output when starting a file. The sound works fine in every...
  16. Replies
    16
    Views
    12,380

    HMM... Time for a little error checking on input?...

    HMM... Time for a little error checking on input? :rolleyes:
  17. Replies
    3
    Views
    1,216

    Jon, Are using a profile toolpath? it should...

    Jon,

    Are using a profile toolpath? it should be available, then.
  18. Replies
    11
    Views
    3,009

    I've noticed that in the past as well. Can't...

    I've noticed that in the past as well. Can't change direction before the data stream has finished, it appears.
  19. Thread: New ShopBotter

    by ssflyer
    Replies
    6
    Views
    2,095

    Hi Chip! Welcome to the wonderful,...

    Hi Chip!

    Welcome to the wonderful, frustrating, exhilarating world of CNC! There is always a learning curve, but you are definitely in the right place to find answers!
  20. Replies
    18
    Views
    10,901

    Any chance it will go back to displaying real...

    Any chance it will go back to displaying real names, instead of login names?
  21. Replies
    42
    Views
    17,299

    Outstanding G. Something I'm sure your son...

    Outstanding G.

    Something I'm sure your son will be proud to display his watches with! ;)
  22. Thread: Site error

    by ssflyer
    Replies
    0
    Views
    3,225

    Site error

    Hi,

    Got this when clicking "search" in the breadcrumb.

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=24369&stc=1
  23. Replies
    3
    Views
    4,124

    When starting, I found local cabinet shops to be...

    When starting, I found local cabinet shops to be a great resource. Make them a simple sample plaque or sign, with their logo, and get everything from cutoffs to corian! It can also increase your...
  24. Replies
    17
    Views
    5,588

    Great idea, John! I know there have been times I...

    Great idea, John! I know there have been times I could have used it! :o
  25. Replies
    34
    Views
    14,446

    Steve, You can also take a look at your pasted...

    Steve,

    You can also take a look at your pasted text in source mode on the forum post (first icon on the top left) and see exactly what is being pasted.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4