Search:

Type: Posts; User: Red F

Page 1 of 4 1 2 3 4

Search: Search took 0.41 seconds.

  1. Thread: Forum Jibberish

    by Red F
    Replies
    4
    Views
    212

    I believe that is where the computer doesn't...

    I believe that is where the computer doesn't recognize quotation marks or something like that. Like this "
  2. Replies
    8
    Views
    296

    DWG is autocad. If there is a drafting teacher...

    DWG is autocad. If there is a drafting teacher at your high school, they may have software that could open it. Otherwise see if he has it saved as a DXF. Aspire can import those.
  3. Replies
    1
    Views
    189

    More CFM is more better.

    More CFM is more better.
  4. Thread: Hole not round

    by Red F
    Replies
    7
    Views
    740

    I found when I was running my router with a climb...

    I found when I was running my router with a climb cut on small holes at high feed rate, my holes looked like yours. I had a little slop in the machine like bill.young just talked about and the climb...
  5. Replies
    11
    Views
    1,118

    I'm sorry that I am no help answering your...

    I'm sorry that I am no help answering your question, but I am curious about your vacuum setup. I'm trying to work out some vacuum workholding form my machine and I wonder, are each of your pods...
  6. Replies
    5
    Views
    891

    Just from what I remember looking at the one I...

    Just from what I remember looking at the one I used to own. I believe that if you run your table too far back, it bumps into that bolt and kicks the stepper motor out a tiny bit so that it doesn't...
  7. Replies
    11
    Views
    1,392

    Thank you for the clarification Eric. I...

    Thank you for the clarification Eric. I appreciate it.
  8. Replies
    11
    Views
    1,392

    Thank you Eric for the recording of the Webinar. ...

    Thank you Eric for the recording of the Webinar.

    I played with the calculator a little bit and one thing I am a little confused on is the relationship between depth of cut and chipload. It is...
  9. Thread: Table legs

    by Red F
    Replies
    13
    Views
    1,569

    Reminds me of this old thread. ...

    Reminds me of this old thread. http://www.talkshopbot.com/forum/showthread.php?24604-White-oak-table

    He was building 4 sides for each leg and mitering them together
  10. Replies
    4
    Views
    1,155

    One possibility is that your bit isn't truly 120...

    One possibility is that your bit isn't truly 120 degrees or 90 degrees. That would cause over-cutting in the corners like you see on the body of the "I". You can test out cutting some sample...
  11. Thread: 4x8 prt standard

    by Red F
    Replies
    12
    Views
    4,664

    I'm guessing it is in Cookeville TN

    I'm guessing it is in Cookeville TN
  12. Thread: Is CNC cheating?

    by Red F
    Replies
    25
    Views
    6,737

    I know I'm kind of a smart ass, but I named my...

    I know I'm kind of a smart ass, but I named my router "Hand". Got around that "hand made" problem.
  13. Replies
    9
    Views
    2,196

    Eric, that model is great and I'm digging that...

    Eric, that model is great and I'm digging that table you have the model on. We are setting up a new to us non-blue CNC at work and I need to build an off-load table for it. I think I'll try to do...
  14. Replies
    14
    Views
    5,034

    It looks like the tool path is not set for a 60...

    It looks like the tool path is not set for a 60 degree bit, or your z is not zeroed correctly.
  15. Replies
    24
    Views
    5,780

    I bought a Makita track saw to save a little...

    I bought a Makita track saw to save a little money over the festool. The quality wasn't good enough for me, so I sent it back and bought the smaller Festool corded saw (TS55?). I couldn't be...
  16. Thread: Collet help

    by Red F
    Replies
    9
    Views
    1,897

    precise bits has a 1/8" collet and nut for some...

    precise bits has a 1/8" collet and nut for some router models.

    https://www.precisebits.com/gateways/ColletsNutsHome.htm
  17. Replies
    9
    Views
    3,468

    Appears to be a standard. There is red on the z...

    Appears to be a standard. There is red on the z axis motor
  18. Replies
    27
    Views
    8,781

    http://www.talkshopbot.com/forum/showthread.php?19...

    http://www.talkshopbot.com/forum/showthread.php?19903-Buddy-BT48-Alpha-table-MKIII&highlight=buddy+table

    Check out this thread. This is a great aluminum vacuum table built on a Buddy.

    Truely...
  19. Replies
    16
    Views
    4,558

    Brady, Iím trying to picture how a dial indicator...

    Brady, Iím trying to picture how a dial indicator can be used to true up the z-axis without something to offset it like the aforementioned shiny object.
    Would you mount it to the table and chuck a...
  20. Replies
    4
    Views
    2,563

    This has been sold and driven halfway across the...

    This has been sold and driven halfway across the country
  21. Replies
    23
    Views
    6,487

    It may be your surfacing pass and not your second...

    It may be your surfacing pass and not your second cut.

    Could a dull surfacing bit cause push itself up as it cut, or push the table material down?

    When I'm problem solving, I try not to take...
  22. Replies
    4
    Views
    2,563

    Sale pending.

    Sale pending.
  23. Thread: IBILD.com

    by Red F
    Replies
    21
    Views
    15,969

    That is a constant battle for our website guy at...

    That is a constant battle for our website guy at work. I happily only know a little about it.
  24. Thread: IBILD.com

    by Red F
    Replies
    21
    Views
    15,969

    I looked at the site on an Iphone SE. Some of...

    I looked at the site on an Iphone SE. Some of the section title words have to go onto multiple lines due to their font size and length. Also the animated typing bit at the end causes the FAQ part...
  25. Replies
    4
    Views
    2,563

    2008 Buddy 32 standard for sale

    Iím putting my 2008 Buddy 32 standard up for sale. Iím asking $5000 for it. I bought it from the original owner in 2011. In both of its lives it has seen minimal use. The first owner was a...
Results 1 to 25 of 97
Page 1 of 4 1 2 3 4