Search:

Type: Posts; User: Hobodog2

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    8,155

    Aluminum Feeds & Speeds

    I have some .066 thick aluminum sign faces for a Wendy's that I need to cut. I don't know the material hardness, seems fairly hard.

    I am using a downshear .25" aluminum bit from Amana. I have...
  2. Replies
    5
    Views
    4,895

    WinRemote Server Issues

    Scott

    I am using the iPhone ShopBot remote application with the WinRemote Server on the PC. I have used it for 2 years with two different iPhones and different PCs (as I upgraded them). It even...
  3. Replies
    5
    Views
    4,895

    Win Remote Server Issues

    Hi Scott

    Thanks for the reply.

    I am doing everything the same as the past two years or so when using WinRemote for the ShopBot SB3 control, but it stopped working somewhere along the line.

    I...
  4. Replies
    5
    Views
    4,895

    Win Remote Server Issues

    My WinRemote control of my PRT Alpha using my iPhone stopped working.

    I think it was when I upgraded from Win 8.0 to 8.1 Prior to that it was working fine under Win 8.0

    The...
  5. Disregard, I found a broken wire at the probe's...

    Disregard, I found a broken wire at the probe's WAGO connector.
  6. Probe Stopped Working after PC and Control Software Upgrade

    I am running a PRT Alpha with 7.2 gearboxes.

    I upgraded my control PC with a Win 8 PC and downloaded new control software and I upgraded the firmware.

    Problem: Output #4 (stops the ShopBot)...
  7. Replies
    3
    Views
    2,894

    Reversed Z Travel in Keypad Mode

    Thanks Brady, actually, I did put the - sign in the UV for the Z value earlier and that worked.

    I will try the .ini trick tomorrow, although it is a new PC with a new Control software load so not...
  8. Replies
    3
    Views
    2,894

    Reversed Z Travel in Keypad mode

    I installed a new Windows 8.1 PC to run my PRT Alpha 7.2 machine and now the Z travel is reversed in Keypad mode (Up arrow moves Z down and vice verse).

    Must be a setting somewhere, can anyone...
  9. Replies
    2
    Views
    3,861

    OK, thanks Brady. I will advise if I go that...

    OK, thanks Brady. I will advise if I go that route.
  10. Replies
    2
    Views
    3,861

    Exporting Part Wizard Drawing files

    Anyone know a way to import the old Part Wizard drawings into Aspire or another drawing program?

    Thanks, Pete
  11. Replies
    15
    Views
    8,908

    As the originator of this thread I want to...

    As the originator of this thread I want to provide some closure - maybe others are having the same problem; intermittent operation of the Win Remote Server.

    It turns out that my iPhone is the...
  12. Replies
    15
    Views
    8,908

    Roger Thanks for the reply. All my IPs check...

    Roger

    Thanks for the reply. All my IPs check out OK and the darned application has worked in the past, albeit intermittently.

    So, I will keep looking around and see if I can find something.
    ...
  13. Replies
    15
    Views
    8,908

    Win Remote Server Issues

    I cannot get the Win Remote Server application on my iPhone to control the ShopBot.

    1. Win Remote Server is running and minimized in the system tray.

    2. Win Remote Server application is running...
  14. Replies
    5
    Views
    3,883

    Thanks for the input Mike - I have had bad luck...

    Thanks for the input Mike - I have had bad luck with .080 aluminum before, I will try your settings.
  15. Replies
    5
    Views
    3,883

    Speeds and Feeds for .080 Aluminum?

    Can anyone suggest proper speeds and feeds for cutting .080 Aluminum?

    I am using Amana .250 Aluminum cutting bits. Also, what pass depths do you recommend.
  16. Replies
    3
    Views
    5,023

    Thanks Brady, worked a treat - it has been years...

    Thanks Brady, worked a treat - it has been years since I did that and could not remember which pull down item (TS) to use.
  17. Replies
    3
    Views
    5,023

    XY Proxy Switch Offset Setting

    Can someone remind me how to set the X,Y home setting - the offset from the prox switch when you do the C3 routine. The book says to modify the home.sbp file - but I don't seem to have that file on...
  18. Replies
    3
    Views
    3,291

    Chris - is this done with a rotating bit or a...

    Chris - is this done with a rotating bit or a static bit. What size, taper, etc bits do you use pls.
  19. Replies
    3
    Views
    3,291

    Brass Plate Engraving

    What bit should I use to engrave text on a 1.5" x 5" Engraver's Brass plate. And do you have a source for the bit pls.

    It is a memorial plate to be used outdoors. It has two lines of text.
    ...
  20. Replies
    0
    Views
    2,026

    HDPE Sheet Goods needed

    Anyone have a source on the West coast for .5" HDPE 4'x8' sheets. I am looking for a White-Black-White configuration.

    I am aware of 3 brands; ColorCore, Signboard and PolyCarve.

    Anyone know of...
  21. Thread: Baseball bats

    by Hobodog2
    Replies
    13
    Views
    9,996

    Baseball Bats

    Michael

    How did you engrave the logos - especially on the end of the bats.

    Thanks, Pete
  22. Replies
    10
    Views
    5,974

    All good information and solutions to work...

    All good information and solutions to work positioning - but I think there may be other solutions out there as well - anyone else care to share their methods?

    Gary, do you have any Fabco part...
  23. Replies
    10
    Views
    5,974

    Air Operated Positioning Posts

    Thank you both for that information - I have not looked at those columns for years - boy, have I missed some good information.

    Super - thank you
  24. Replies
    10
    Views
    5,974

    Air Operated Positioning Posts

    Does anyone have a source and part numbers for air operated positioning posts that you would mount to the edge of the work surfaces (spoil board and base board) to allow accurate positioning of...
  25. Replies
    6
    Views
    4,042

    RPM Dialog Box

    Does use of the RPM Dialog Box require a special cable between the spindle control box (in my case the Delta box) and the ShopBot control box?
Results 1 to 25 of 53
Page 1 of 3 1 2 3