Search:

Type: Posts; User: Ken Sully

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    24
    Views
    1,993

    Steve, Beautiful table and wood grain. I tell...

    Steve,
    Beautiful table and wood grain. I tell everyone my favorite tool is the track saw! I find myself using it for a variety of things. The saw has cut lots of board feet and still going strong!
  2. Replies
    24
    Views
    1,993

    Ouch...Good idea for repair. No blood no problem!...

    Ouch...Good idea for repair. No blood no problem! As they say if you can fix it with money........
    Great looking wood!
  3. Replies
    24
    Views
    1,993

    Steve, Let us know how you like it!!

    Steve,
    Let us know how you like it!!
  4. Replies
    24
    Views
    1,993

    Steve, My favorite tool in my shop is the...

    Steve,
    My favorite tool in my shop is the Festool track saw. It's a little pricey but is well made. They make 2 sizes of saws, the bigger has a cut depth of 2.75. You lay the track on the work. The...
  5. Replies
    4
    Views
    622

    Sent you a PM

    Sent you a PM
  6. Replies
    35
    Views
    19,524

    I only have one. What was interesting is another...

    I only have one. What was interesting is another shop botter was having the same problem. We talked several times. He also ended up purchasing the main control board and his problem also went away
  7. Replies
    35
    Views
    19,524

    Not sure if this helps, but I was having an estop...

    Not sure if this helps, but I was having an estop error on my PRS Alpha. I tried everything including sending the main board to showboat for them to test. They sent it back saying nothing wrong with...
  8. Replies
    5
    Views
    719

    Great ideas! I think numbering each space is the...

    Great ideas! I think numbering each space is the way to go. That way as the brews change all you have to do is look for the number. Thinking of a 2D airplane layout (beer flight).
  9. Replies
    5
    Views
    719

    Thanks Scott there are some good ideas

    Thanks Scott there are some good ideas
  10. Replies
    5
    Views
    719

    Beer Flight Holders

    Has anyone made a beer flight carving. There are so many micro brews that have basic holders. Looking for some ideas
  11. Just a final thought. How old is your DC? Could...

    Just a final thought. How old is your DC? Could you have a motor failing causing electrical noise in the ground leg? Seems odd the only time you have trouble is when its turned on.
  12. I agree with Jim. I you have two different...

    I agree with Jim.
    I you have two different grounds you will end up with dissimelar grounds and current can flow between them. Make suer your system is tied to the same ground. Not one from the house...
  13. Replies
    7
    Views
    3,494

    Here is another idea. Maybe 2 wheels at a time? ...

    Here is another idea. Maybe 2 wheels at a time?


    https://www.youtube.com/watch?v=AmGirrDI3jU
  14. Replies
    4
    Views
    971

    I used 3M white scotch pad to buff before the...

    I used 3M white scotch pad to buff before the final finish. It didn't need much else. The long cuts are a problem (Fire) if you are not near but. I use a baby monitor when I am not in the shop. My...
  15. Replies
    4
    Views
    971

    .0625 and 39 Hours Later

    This is Walnut 5.5" x 96.0" 1"thick. With advice from Scott cut with .0625 ball nose. Very happy with results. Shopbotters allow me to turn out cool stuff. Worried a power glitch could hurt me with...
  16. Replies
    8
    Views
    1,170

    Brush for Wheels

    I got a brush from John Deere used in a corn planter. Cost 6-12.00 can't remember. Our brush will do all of the wheels. Used a bolt with fender washer to capture the brush. Works fine
  17. Might be smart to drive a 24 volt relay. That way...

    Might be smart to drive a 24 volt relay. That way the relay contacts can supply the voltage/current your accessory requires. The relay load should be low.
    Check the current draw of the relay coil....
  18. Replies
    12
    Views
    2,464

    Don't know if this helps, but they have a large...

    Don't know if this helps, but they have a large selection. Located in Kansas and Iowa. Finally something good about living in Iowa!! Very few CNC guys, at least Shopbot.

    ...
  19. Replies
    19
    Views
    7,466

    A friend told me about this and it works great!...

    A friend told me about this and it works great! No more clamps,screws,naile or need of a vacuum. Take a look give it a try and let me know how it works for you

    ...
  20. Thread: Makers Mark

    by Ken Sully
    Replies
    4
    Views
    1,588

    Keith, Nice job! I must admit I was a little...

    Keith,
    Nice job! I must admit I was a little disappointed..... I was looking for Makers Mark bourbon!!
  21. Thanks Bob Couldn't find that for the life of me!

    Thanks Bob
    Couldn't find that for the life of me!
  22. Trying to find the link, or post for Gary C's...

    Trying to find the link, or post for Gary C's dovetail procedure. Can't seem to find it.
    Anybody know where to find it?
  23. Replies
    0
    Views
    829

    Home Made CNC on Craigs List

    Didn't notice shopbpt only
    Sorryy
  24. Replies
    6
    Views
    1,743

    Talking to a fellow botter he made a good point....

    Talking to a fellow botter he made a good point. We see many problems posted on this site but seldom hear the outcome.
    After several calls to Shop Bot and sending both the mother board and control...
  25. Replies
    6
    Views
    1,743

    Bob, I actually used a clip lead to jump the...

    Bob,
    I actually used a clip lead to jump the fuses. After another day of talking to Shop Bot support ordered a new control board, there is nothing left. My fellow botter in Tenn with the exact...
Results 1 to 25 of 174
Page 1 of 7 1 2 3 4