Search:

Type: Posts; User: 8Ball

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    434

    Apparently he doesn't want to sell. I've...

    Apparently he doesn't want to sell. I've contacted with no response. He was on yesterday at 2:13PM.
  2. Replies
    2
    Views
    459

    This was for sale in September for $4500. What...

    This was for sale in September for $4500. What makes it worth $2000 more now?

    There weren't any replies to the inquiries either.
    ...
  3. Thread: PVC Sign

    by 8Ball
    Replies
    7
    Views
    689

    Those fuzzies can be cleaned up by using a piece...

    Those fuzzies can be cleaned up by using a piece of sandpaper, and going around the corners of the cuts with gentle pressure. Gives the paint a crisp edge.
  4. Replies
    7
    Views
    567

    Continue the angled trim line down to where it...

    Continue the angled trim line down to where it meets the top of the bottom trim. Red line.
    Your angle is the green line.



    https://i.imgur.com/m04huv6.jpg
  5. Replies
    15
    Views
    1,137

    Like I said, all options listed, will look like...

    Like I said, all options listed, will look like poo. Very noticeable. With the exception of drywall work, and that is work.
    You didn't mention if the overhead cabinets fit properly in the corner....
  6. Replies
    15
    Views
    1,137

    So, your counter top was built out-of-square?...

    So, your counter top was built out-of-square?
    Anything you do, will look terrible with that amount of gap. I would cut the counter top, and square it. If you don't have enough material to get it cut...
  7. Thread: Wanting to Sell

    by 8Ball
    Replies
    7
    Views
    1,277

    There is another big name brand, that has a...

    There is another big name brand, that has a larger footprint and more ridged, that can be had for less when they are available.
    There was just a 2'x3', only a couple years old with low hours, that...
  8. Replies
    2
    Views
    914

    That's a complicated set-up to run t-mold. We...

    That's a complicated set-up to run t-mold.
    We have the router mounted in the table with an adjustment plate for height. There's a hold down roller mounted in the overhead dust cover, that holds the...
  9. Thread: White oak table

    by 8Ball
    Replies
    18
    Views
    2,935

    I can get 8/4 quarter sawn white oak for $4.83/...

    I can get 8/4 quarter sawn white oak for $4.83/ bd. ft.
    I can also get several exotics for the same price in 4/4 rift sawn.
  10. Replies
    6
    Views
    882

    Using VCP, you can also cut several pockets of...

    Using VCP, you can also cut several pockets of various sizes and depths using a single toolpath, provided they all use the same cutter.
  11. Replies
    4
    Views
    3,101

    How much are you asking? Is it in...

    How much are you asking?
    Is it in running/operating condition?
    What software is included?
  12. Thread: Hand gun grips

    by 8Ball
    Replies
    4
    Views
    1,495

    It depends on the grips you are looking for. I...

    It depends on the grips you are looking for. I have files for the 1911.
  13. Replies
    11
    Views
    3,932

    I would be a little concerned about the...

    I would be a little concerned about the maintenance of the landscape.
    In the attached photo, it looks like it's very neglected.
    What's the point of having a sign, if it isn't attractive and gives...
  14. Replies
    26
    Views
    7,304

    For a sign like that, i probably would have used...

    For a sign like that, i probably would have used color core since there isn't any painting required or as suggested, Corian. Corian is inexpensive for smaller pieces and is very easy to work with. I...
  15. Replies
    3
    Views
    1,270

    I did a quick check, without knowing the length...

    I did a quick check, without knowing the length of the bottom, I used 25".
    The top of the lid comes out to 51.3 degrees and the bottom of the lid is 38.7 degrees. That's using no angles on the front...
  16. Replies
    3
    Views
    1,270

    Any cad type program will give the exact angle....

    Any cad type program will give the exact angle. What is the length at the bottom? With that and the dimensions you already have, it would be simple to figure the angle.

    For the table saw, build a...
  17. Replies
    4
    Views
    2,060

    Look in your font library. There are usually...

    Look in your font library. There are usually several script fonts and most work well for those signs. I've made many with different words using various fonts.
    You could also look at dafont.
  18. Replies
    17
    Views
    4,502

    Could you elaborate on your comment? Is there...

    Could you elaborate on your comment?
    Is there something better than Mach3?
    I'm fairly new to cnc and I use Mach3, but if there is something better, I could be interested.
  19. I would like to see a pic from underneath,...

    I would like to see a pic from underneath, showing how it's mounted and how the brackets get tucked away when it's folded down.;)
  20. Replies
    12
    Views
    2,533

    That sounds REALLY dangerous. Initiating kickback...

    That sounds REALLY dangerous. Initiating kickback isn't recommended.
  21. Replies
    4
    Views
    2,250

    I'm just guessing from similar plaques I've made....

    I'm just guessing from similar plaques I've made.
    Red oak, v-carved and painted in with black paint. Then sanded and a poly to protect it.
  22. Replies
    30
    Views
    6,970

    I would suggest using an 1/8" end mill vs. the...

    I would suggest using an 1/8" end mill vs. the 1/4" if you would like to retain the detail to some extent.

    I did a quick model using the 1/8" , this is how it previews...
  23. Replies
    2
    Views
    2,372

    It really depends on the alloy, but yes a carbide...

    It really depends on the alloy, but yes a carbide core bit will cut alum.
    I cut a lot of 6061 alum and use carbide bits without any issues. You will need to take several passes to that depth
    and...
  24. I came up with this... ...

    I came up with this...


    http://i1025.photobucket.com/albums/y320/H2ODan/D.%20Tig_zpsgem7fnov.jpg
  25. Replies
    48
    Views
    16,279

    I have seen your posts and pics of your signs....

    I have seen your posts and pics of your signs. Not that they don't look good, but they are no different than the hundreds of signs in my area.
    There is nothing that distinguishes your signs from...
Results 1 to 25 of 29
Page 1 of 2 1 2