Hi Everyone-
A muralist friend has asked me if I can make a "large tree" for an office project he's quoting. The trunk needs to be 11ft high and around 15-20" in diameter. The upper portion of the...
Type: Posts; User: john_hartman
Hi Everyone-
A muralist friend has asked me if I can make a "large tree" for an office project he's quoting. The trunk needs to be 11ft high and around 15-20" in diameter. The upper portion of the...
Here is the fix to the MTC file to allow zeroing to the spoilboard.. will allow the bit to start cutting to the top of the 3/4" material instead of the spoilboard. It works. Tech support doesn't know...
Disregard #4. I completely forgot to calculate offsets between bit and drill. thx
So after 8 years of moderate use my PRSalpha 9648 is developing issues. Recently had to change the y motor/driver, now looks like the x's need to be replaced as well.
This past week had the...
One of my x axis motors has a lot of wobble. Also, has a couple chipped pinion teeth and needs to be replaced.
Apparently these motors are no longer made. I thought I would check here before I...
I'm looking for someone who has the ability to produce some pretty ornate chairs and dining table. They don't have to be an exact match just capture look and feel. I would be looking to outsource...
This worked great! Many thanks!
This will take me some time figure out. Unfortunately I'm not a propeller head..:) Thanks
Ok thanks Terry. I will look into that. It's just not the same without Gary..:)
Dual I believe. There is a red sleeve to manually keep air on/off and the drill cycles on/off between holes being drilled.
I believe there is a way to write some simple code in the "machine settings" under "header/footer tab" to command the spindle to go to a designated area after sheet has been finished.
Any help...
Hi All-
I'm using a shop bot air drill on my PRS Alpha and using ecabinets. The issue I'm having is that the air drill turns "on" right as the bit touches the surface of ply. This leaves a slight...
I have a curved desk which I need a cut file. I've been using ecabinets for 3 years but have no idea how to go about creating a curved cabinet.
See the attached measured drawings. There is a...
thanks for the suggestions!
Looking for a source to buy a .25 or .375" bit that is 5" to 6" long
How much to make me a set?
I pay $64 per sheet for 3/4" 2 sided pre-finished. I have been using this product for ALL inside cabinetry for 6+ years with no finish failure. Its a UV cured finish that's tougher than anything you...
Does anyone have an issue with getting a smooth cut with 3/4" Columbia pure bond with the link? I get these bulges along the entire length of the cut.
I cut 90% through in climb then all the way...
Andrew- Thanks for the info. That is exactly what I was looking for..:D
Unfortunately I won't have time to do a test run. But it sounds like I should be dealing minimal shrinkage using an MDF core. Would it be a bad idea to glue the panel all the way around the rails and...
For all those cabinet makers out there... I've been outsourcing doors for larger kitchen projects. I have one that is to be painted. I've only ever fabricated my own doors when painted.
In the...
I called both Edgeco and DC- dist. Edgeco say they can do it for $94/250ft. They need a 12" sample takes 2-3 weeks. Apparently its a new service for them. DC- had never heard of this request but said...
I searched woodweb for this and there was a little bit of discussion but not what I was looking for.. I am starting to get into more frameless cabinetry and until recently the exterior has been...
I'm running a new PRS Alpha with 2.2 HSD and air drill. The following issue is something that I have been "living with" on my old machine but would like to try get it resolved.
Two issues-
1)...
The weekend's are pretty busy but the week days are a bit boring. If you want to come down call me 513-6859; I have extra tickets. Aetna only takes checks or cash.. I may have to order it for you and...