Search:

Type: Posts; User: banjomanwv

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Like a dummy I never thought to contact Brady but...

    Like a dummy I never thought to contact Brady but he has been kind enough to walk me through it and help me out and he's all the help I need I should have thought to ask him in the first place so if...
  2. Looking for shopbot owner around Charlotte North Carolina

    I recently had Brady Watson do some 3D scans for me and he did an amazing job. One was for a banjo neck and guitar neck and I'm having a bear of a time trying to get one cut out successfully I was...
  3. Replies
    3
    Views
    731

    32064If you send me your email I can send you...

    32064If you send me your email I can send you specs . Id like to know the cost of this new
  4. Replies
    3
    Views
    731

    Regenerative blower with filters

    Purchased a shopbot and this was part of the package if I'm not mistaken this setup was sold by shopbot and may still be regenerative blower with valve filter air regulator I hooked it up it works...
  5. Replies
    4
    Views
    433

    Its reading 12.0 so im guessing thats 12000 rpm ?

    Its reading 12.0 so im guessing thats 12000 rpm ?
  6. Replies
    4
    Views
    433

    Thank you while I have that hook up my control...

    Thank you while I have that hook up my control board doesn't have the correct card in it to run it from the software so I have to run the vfd manually
  7. Replies
    4
    Views
    433

    VFD Controls

    Just got my new spindle hooked up to my buddy and I can't figure out how to control the vfd. I understand I'm looking at Hertz and not RPM and how to convert that but I'm not quite for sure I...
  8. Replies
    14
    Views
    3,556

    They do but this is the first time I've ever...

    They do but this is the first time I've ever fooled with anything like this I didn't even know they snapped open
  9. Replies
    14
    Views
    3,556

    Got everything hooked up just have to hook up the...

    Got everything hooked up just have to hook up the 2:40 now and I'll be rolling
  10. Replies
    14
    Views
    3,556

    they sent the wrong ones but I rigged something...

    they sent the wrong ones but I rigged something up.......now to run the cables and get them hooks up to the control box
  11. Replies
    14
    Views
    3,556

    Thanks Eric and Brady I can now see where the...

    Thanks Eric and Brady I can now see where the orange cord goes but any idea what the two big brackets are for? Are they supposed be used to hang the vfd with? I don't see those in Eric's picture
  12. Replies
    14
    Views
    3,556

    okay since the orange wire is already wired up to...

    okay since the orange wire is already wired up to the box on one end and has the attachment to hook to the spindle on the other I guess I'm going to have to unwire it to run it through correct?
  13. Replies
    14
    Views
    3,556

    Does the orange cable go in the echain with the...

    Does the orange cable go in the echain with the other wires?
  14. Replies
    14
    Views
    3,556

    31768 31769

    31768
    31769
  15. Replies
    14
    Views
    3,556

    Installing spindle

    So I just purchased a kit to install a spindle on my buddy 32 standard. I installed the 24 volt box and on the other end of it's going to be the fan for the spindle and I've got the spindle mounted...
  16. Ok I think Chris Burns is going to be able to do...

    Ok I think Chris Burns is going to be able to do it.....awesome,...thanks
  17. Need Help in the Charlotte Area with my Shop bot

    Upgrading from a router to a spindle (single phase) on a shop bot buddy and have no idea where to start. Is there anyone in the area could hire or get to install?
  18. Thread: Radius disk

    by banjomanwv
    Replies
    0
    Views
    408

    Radius disk

    Does anyone out there have an idea how i can make a radis dish using aspire? 36 radous and the radis part arpund 13 inches. I need male and female part
  19. Replies
    1
    Views
    913

    Need help and advice

    Im a shop ot owner of a few years amd today i purchased my 3rd one with the other 2 being desktops. This is a buddy 48 with a 14z. Its got a router but fof noise i need a spindle.....is the hsd from...
  20. Replies
    1
    Views
    641

    Wtb/wtt for shop bot buddy or 4x4

    Looking for a shopbot CNC with spindle. We have owned two desktops in the past and use them in our business but we're looking for one a little larger like a 4 by 4 or a buddy 32 or 48. If we could do...
  21. Replies
    9
    Views
    2,263

    is it the 5.5 Z?

    is it the 5.5 Z?
  22. Replies
    0
    Views
    622

    WTB buddy 32 with Spindle

    I have seen a few that sold here or on ebay for 4400 and 5K respectively if you have one for sale give me a shout, im located in NC and very interested in buying. Don't have room for a 4x8
  23. Replies
    8
    Views
    2,778

    Gene your inbox is full an I cant send you a...

    Gene your inbox is full an I cant send you a message
  24. Replies
    8
    Views
    3,201

    you guys who have them for sale, contact me as im...

    you guys who have them for sale, contact me as im looking to buy
  25. Replies
    0
    Views
    507

    Mandolin building

    I am a banjo maker and have a Shopbot desktop. I want to build myself my own personal mandolin and I was wondering if anyone had any advice, programs they want to share etc? Especially for the tops...
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4