Search:

Type: Posts; User: bobmoore

Page 1 of 18 1 2 3 4

Search: Search took 1.46 seconds.

  1. Replies
    1
    Views
    1,177

    Thank you. Machine has sold.

    Thank you. Machine has sold.
  2. Replies
    1
    Views
    1,177

    2016 PRS Standard 96"x48" (Z is 8")

    Set up with 4-zone vacuum system, includes vacuum plumbing but not vacuum pumps. They will be listed later this week.
    Runs completely on 120V circuit
    Includes computer, monitor, cabinet, Vectric...
  3. Replies
    2
    Views
    1,212

    That is an amazing increase, what did you do to...

    That is an amazing increase, what did you do to increase vacuum that much?
  4. Replies
    1
    Views
    977

    FOR SALE: Router bits and Routers

    I have some stuff for sale. Cleaning out the shop. Will be more coming later as well. Pricing does not include shipping.

    Router Bit
    Vortex 5/8” Shank 2270 Solid Carbide upcut 2-flute
    $175
    ...
  5. Replies
    23
    Views
    12,241

    I use MDO as a base which is much more stable...

    I use MDO as a base which is much more stable than any other plywood that I have worked with. I put corian on top of that with the vacuum grid (4 zones) carved into it. The spoilboard tops off the...
  6. Replies
    4
    Views
    1,538

    Pretty normal here in northern WI. Maybe 8 -10...

    Pretty normal here in northern WI. Maybe 8 -10 days in the upper 80's and the air con running. Kinda dry after a wet spring and early summer but maybe the lake levels will recede some. Crazy busy...
  7. Replies
    6
    Views
    2,848

    Very nice article. Thanks for posting.

    Very nice article. Thanks for posting.
  8. Thread: Collet

    by bobmoore
    Replies
    13
    Views
    5,256

    So far I have only seen the bug when I paused...

    So far I have only seen the bug when I paused during a Z motion. Happened on my prt and my prs.
    Collets should be replaced every 2000-3000 hours of use since they do wear out. Plunging up to the...
  9. Thread: Collet

    by bobmoore
    Replies
    13
    Views
    5,256

    I have vcarve pro and when the machine is moving...

    I have vcarve pro and when the machine is moving in the Z direction and I pause the program with the space bar the bit will plunge until it is mechanically stopped when I resume the cut. I can't help...
  10. Replies
    8
    Views
    3,088

    I always like to see Brians posts. Ingenius

    I always like to see Brians posts. Ingenius
  11. Replies
    16
    Views
    7,787

    you can just sand the edges with a foam sanding...

    you can just sand the edges with a foam sanding block.
  12. Replies
    16
    Views
    7,787

    I would just cut rectangles on the table saw and...

    I would just cut rectangles on the table saw and fasten the plexiglass to 2 4 x 4's running perpendicular to plexi for your pass through. Attach with angle brackets.
  13. Replies
    17
    Views
    5,595

    I used corian for mine and it is very stable. I...

    I used corian for mine and it is very stable. I gained quite a bit of vacuum but I no longer remember exact numbers. I switched to 2 5 horse becker vacuum pumps with 4 zones, the smallest being 36...
  14. Thread: Tool Cabinets

    by bobmoore
    Replies
    11
    Views
    6,245

    Nice strong design Brian. How did you eliminate...

    Nice strong design Brian. How did you eliminate tearout on all those dadoes?
  15. Replies
    8
    Views
    6,196

    looks to me like you only need 1.25 inches cut...

    looks to me like you only need 1.25 inches cut length. put the blank on the table and mill the top with a fluting program to achieve the taper. Bob
  16. the extra time it takes to run a 6 percent...

    the extra time it takes to run a 6 percent stepover will be a lot less than the time it takes to fix it by hand and the result is better.
  17. Thread: Collet help

    by bobmoore
    Replies
    9
    Views
    7,514

    Some metal parts are shipped with a rust...

    Some metal parts are shipped with a rust preventative coating that would clean off with kerosene or some other solvent.
  18. Replies
    8
    Views
    13,697

    your 2 inch edge grain will work fine and also be...

    your 2 inch edge grain will work fine and also be more stable than the flat grain.
  19. Replies
    6
    Views
    10,737

    an excellent post John. I don't know if I will...

    an excellent post John. I don't know if I will ever have a use for it but it is filed away for future reference.
  20. Thread: Vacuum Nozzle

    by bobmoore
    Replies
    9
    Views
    12,374

    would you post more about the details of your...

    would you post more about the details of your modification? Looks really good.
  21. Replies
    14
    Views
    30,429

    show a snap shot of your vectors. I think you...

    show a snap shot of your vectors. I think you might be carving a single line font and choosing your cut depth incorrectly. your vectors will tell the story.
    Bob
  22. Replies
    16
    Views
    33,503

    great work as usual Russ

    great work as usual Russ
  23. Replies
    28
    Views
    43,007

    Mike in my opinion as a sign maker the story that...

    Mike in my opinion as a sign maker the story that your sign is trying to tell is about God or Jesus and how your church interacts with them. It is not about the logo of the church. Minimize the logo...
  24. A ridged flat fixture is ideal, aluminum or I use...

    A ridged flat fixture is ideal, aluminum or I use corian because I have it in stock. Use a compressible oring that will pull perfectly flat to the fixture with the vacuum on. If your oring stays...
  25. Mike are you planning to vacuum 20-50 and run...

    Mike are you planning to vacuum 20-50 and run them in one run or is 20-50 at each run but 1 at a time? It makes a big difference what vacuum pump is appropriate.
Results 1 to 25 of 449
Page 1 of 18 1 2 3 4