Search:

Type: Posts; User: nat_wheatley

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    1,433

    Cutting 4'x8' sheets into closet organizer parts.

    Cutting 4'x8' sheets into closet organizer parts.
  2. Replies
    11
    Views
    1,433

    Right now I have 4 of the LH vac motors mounted...

    Right now I have 4 of the LH vac motors mounted directly to the underside of my table. I'm thinking about boxing out the back corner of my shop (about 20-25' from the machine, maybe 1 bend..) and...
  3. Replies
    11
    Views
    1,433

    I'd be interested in what you come up for this. ...

    I'd be interested in what you come up for this. I'm on the verge of doing the same for my hold down vacuums.
  4. Replies
    106
    Views
    13,540

    I bought my PRS Alpha 60x96 10 years ago. I...

    I bought my PRS Alpha 60x96 10 years ago. I can't express the amount of time, effort and work that's been needed to get my machine up to the point where it was able to cut satisfactorily and...
  5. Replies
    8
    Views
    1,106

    Thanks Brady!

    Thanks Brady!
  6. Replies
    8
    Views
    1,106

    Thanks. The supply house is actually closer to...

    Thanks. The supply house is actually closer to me than HD, so that might be the better route anyways...
  7. Replies
    8
    Views
    1,106

    Thinking this might be what I'm after: ...

    Thinking this might be what I'm after:
    ...
  8. Replies
    8
    Views
    1,106

    Hadn't seen one that didn't have a plastic...

    Hadn't seen one that didn't have a plastic coating, but will do search now...
  9. Replies
    8
    Views
    1,471

    +1 to this ^

    +1 to this ^
  10. Replies
    8
    Views
    1,106

    Ground Wire for DC

    I have a solid copper wire that runs from the main trunk of my dust collection ductwork down a flexible hose to the dust boot on my machine. Issue is that, over time, and repeated movement, it...
  11. Replies
    11
    Views
    1,798

    I love seeing your projects come to life....

    I love seeing your projects come to life. Beautiful work, thanks for posting.
  12. Replies
    9
    Views
    1,164

    Power went out - mid sheet - then came back on...

    Power went out - mid sheet - then came back on for a second. Cooked Outputs 1-4...
  13. Replies
    9
    Views
    1,164

    Working as it was originally. Thanks to all for...

    Working as it was originally. Thanks to all for the help.
  14. Replies
    9
    Views
    1,164

    Brady, thanks very much. I'll check those 2...

    Brady, thanks very much. I'll check those 2 jumpers Monday am and report back.
  15. Replies
    9
    Views
    1,164

    I’m not able to adjust my RPMs now, until the...

    I’m not able to adjust my RPMs now, until the spindle is actually cutting, which isn’t logical.
  16. Replies
    9
    Views
    1,164

    Thank you, I’ll take a look at the board and see...

    Thank you, I’ll take a look at the board and see if I can find the jumper.
  17. Replies
    9
    Views
    1,164

    VFD Turning on and off

    2008 PRS Alpha 60x96 HSD Spindle

    I just replaced the control board in my machine. The VFD now turns on only when Outputs 1 and 4 are on. VFD (Yakasawa) used to turn on when I turned on my...
  18. Replies
    8
    Views
    1,145

    Looks good, nice to see the machine moving like...

    Looks good, nice to see the machine moving like that. I had a job a few years back cutting cabinet parts (same cabinet over an over) out of 500+ sheets of 3/4"MDF. Toward the end I was cutting at...
  19. Replies
    8
    Views
    1,125

    I used hard felt, pushed against the rail, and it...

    I used hard felt, pushed against the rail, and it works well. It was Gary Campbell's idea. Reply#7 on this post shows how mine is attached:
    ...
  20. Replies
    21
    Views
    3,081

    My original spindle is sitting on a shelf as...

    My original spindle is sitting on a shelf as proof that the warm up makes a difference. It lasted about 2 years with no warm up routine, while it's replacement (always warmed up) is going on 8 years...
  21. Replies
    17
    Views
    5,579

    Andrew, thanks very much.

    Andrew, thanks very much.
  22. Replies
    17
    Views
    5,579

    Andrew, Do you know what pricing is like for...

    Andrew,

    Do you know what pricing is like for the Cabineo fittings?
  23. Replies
    10
    Views
    2,336

    Looks great. I'm always impressed with your...

    Looks great. I'm always impressed with your work, thanks for posting.
  24. Replies
    25
    Views
    3,677

    If you'll be marketing the software toward...

    If you'll be marketing the software toward professional shops, you'll need to offer construction methods comparable to what they're already using.
  25. Replies
    4
    Views
    1,692

    Definitely would love to have one, we'll see how...

    Definitely would love to have one, we'll see how my piggy bank looks once they do become avaiable...GCMF.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4