Search:

Type: Posts; User: sevans

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    945

    Well....I'm pretty sure you might be right about...

    Well....I'm pretty sure you might be right about that. Shopbot will send someone soon to help me out but I'm still tryin! Thanks for your reply!
  2. Replies
    2
    Views
    945

    YZ Car Lower Wheel Bearings

    Hello, I am having troubles with the Lower Wheel Bearings on the YZ Car. For some reason, the one on the right engages, yet the one on the left will not stay engaged...no matter what I do. It...
  3. Replies
    1
    Views
    772

    Gusset T Nut Broken

    Hello,

    After some adjustments that required loosening the Gusset Bolts, I noticed one bolt spinning. It appears as though the T Nut is completely stripped out. Any advice on how to add a bolt...
  4. Replies
    35
    Views
    4,112

    Hey There, have a quick question for you... I...

    Hey There, have a quick question for you... I noticed that there are 2 set screws on the insides of the Aluminum Blocks holding the Z Extrusion. Any idea what those are for?
  5. Replies
    35
    Views
    4,112

    [QUOTE=TomH,ShopBot;200642]Welp, I had it...

    [QUOTE=TomH,ShopBot;200642]Welp, I had it backwards, thanks for clearing it up :cool:

    Bigger pinion not being snug is definitely more likely, I couldn't think of a scenario that the 12mm would be...
  6. Replies
    35
    Views
    4,112

    Sure, I'll send you the specs. But for the...

    Sure, I'll send you the specs. But for the record, it's the original pinions that are a tighter fit (the Browning EN 6418. It is snug enough that it does not click back and forth when you wiggle...
  7. Replies
    35
    Views
    4,112

    Thanks for letting me know that. The shaft on my...

    Thanks for letting me know that. The shaft on my motor measures 12mm. The original opinions were a tight fit. The new ones can spin around on the shaft (without key) not so for...
  8. Replies
    35
    Views
    4,112

    Thank You for the info. Today I realized, and...

    Thank You for the info. Today I realized, and not 100% sure how I feel or anyone else will, that the pinion set I received is slightly bigger than the original. I practically have to hammer on the...
  9. Replies
    35
    Views
    4,112

    Just for the record......... this is the problem...

    Just for the record......... this is the problem I'm having. Been cutting signs like this for years.... Super smooth. Now this and seems to be getting worse....
  10. Replies
    35
    Views
    4,112

    Motor Question

    I just pulled an x motor just to check it out. Took off the pinion (WITH MUCH FORCE). I noticed after that where the set screw hits the shaft of the motor is just mutilated. The key also has so...
  11. Replies
    35
    Views
    4,112

    Yep. I have a spindle square like that. Always...

    Yep. I have a spindle square like that. Always showing out in X Direction.
  12. Replies
    35
    Views
    4,112

    Got it. Consider it done. :)

    Got it. Consider it done. :)
  13. Replies
    35
    Views
    4,112

    I cant envision what you mean by bending it into...

    I cant envision what you mean by bending it into a Z... You mean like this:

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=31355&stc=1
  14. Replies
    35
    Views
    4,112

    PERFECT!!!! Thank You so much

    PERFECT!!!! Thank You so much
  15. Replies
    35
    Views
    4,112

    Absolutely!!! See picture. Let me know if you...

    Absolutely!!! See picture. Let me know if you need to see more. :Dhttp://www.talkshopbot.com/forum/attachment.php?attachmentid=31353&stc=1
  16. Replies
    35
    Views
    4,112

    The Y Beam (or gantry) is not perpendicular to...

    The Y Beam (or gantry) is not perpendicular to the table. It is cocked out a bit at the bottom and obviously what is keeping my spindle from being plumb... Is there a fix for this?
  17. Replies
    35
    Views
    4,112

    EXCELLENT! Thank You

    EXCELLENT! Thank You
  18. Replies
    35
    Views
    4,112

    You know what...I don't know what the problem is....

    You know what...I don't know what the problem is. I have lost sight of it at this point. I started down the "Mechanical Issue" road 2 weeks ago and still nothing. I have removed and replaced the...
  19. Replies
    35
    Views
    4,112

    HAHAHAHA...did I say that? I apologize...For...

    HAHAHAHA...did I say that? I apologize...For some reason I keep calling the Z the X and so forth and so on. Not great for getting support. What I meant is that the V Rollers will never align with...
  20. Replies
    35
    Views
    4,112

    I definitely will send a pic when i get back to...

    I definitely will send a pic when i get back to my shop. Shopbot told me that they would never line up just right. The blocks are securely in place. It appears that something would have to get...
  21. Replies
    35
    Views
    4,112

    i just can't even thank you enough for this...

    i just can't even thank you enough for this information. I have been working at it for quite some time now and am getting so frustrated. It pains me that no matter what the left rollers will never...
  22. Replies
    35
    Views
    4,112

    Z Adjustment Question

    Does anybody out there know how to adjust these? Everything I've found in manual and online is very vague. Many Thanks for reading!
    :D
  23. Replies
    10
    Views
    2,408

    This same thing is happening to me. I have...

    This same thing is happening to me. I have wondered if it is Aspire. However, I did open up an older version to test that and it made no difference. I have completely disassembled everything,...
  24. Replies
    12
    Views
    2,628

    That does make sense. It is jerky for sure. ...

    That does make sense. It is jerky for sure. These letters are 1.5" or so in height. I used a 120 degree her saf bit and fed it at 1.2. Spindle 18000 rpm's. how slow can you feed? Or should I?
  25. Replies
    12
    Views
    2,628

    Are there physical indications of a worn collet? ...

    Are there physical indications of a worn collet? Something in particular I can do/see to tell if it is worn?
Results 1 to 25 of 85
Page 1 of 4 1 2 3 4