Search:

Type: Posts; User: srwtlc

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    2
    Views
    95

    Hey Scott, glad you're back at it! That would...

    Hey Scott, glad you're back at it! That would be MN (Move Nudge).
  2. Thread: Safety Z

    by srwtlc
    Replies
    2
    Views
    339

    VC Safe Z Pull-Up. Otherwise, look at what...

    VC Safe Z Pull-Up.

    Otherwise, look at what your design software is using for home/start position, Z above material, and rapids above material.
  3. Replies
    14
    Views
    5,956

    Ancient indeed! 2012 called and they say it's...

    Ancient indeed! 2012 called and they say it's waaaaay past time to upgrade to some better control software! 12 years past time for SB3!

    That said, when the button window is open, hover your...
  4. Replies
    1
    Views
    287

    I've replaced several of them over the years,...

    I've replaced several of them over the years, until my spindle finally died and was replaced. Check somewhere like Digi-Key for a replacement of the same size, voltage, ball bearing, and cfm.
  5. Replies
    3
    Views
    424

    Do you have an example of what you're trying to...

    Do you have an example of what you're trying to do?

    Have you seen this pdf (C:\Program Files (x86)\ShopBot\ShopBot 3\Help\Calculated_Functions.pdf)?
  6. Replies
    7
    Views
    1,618

    Is your machine an ATC?

    Is your machine an ATC?
  7. Replies
    4
    Views
    592

    Open the file for output and the use the "Write"...

    Open the file for output and the use the "Write" command to write to it by using variables in your file. Variables can be hard coded or set with the input command.

    Sample code to open a file and...
  8. Replies
    4
    Views
    592

    Yes and yes. For writing to the file, look at...

    Yes and yes. For writing to the file, look at OPEN "path&filename" FOR {INPUT/OUTPUT/APPEND} in the programming manual.
  9. Replies
    2
    Views
    427

    Ron, Take a look at something like an Intel...

    Ron,

    Take a look at something like an Intel NUC, or what I like to use for my Centroid Acorn upgrades, are some of the off lease mini business pc's by Lenovo or HP on eBay. Lenovo M93p and up or...
  10. Replies
    3
    Views
    1,796

    Check the settings for the tool with the edit...

    Check the settings for the tool with the edit button in the Aspire toolpath, what is the rpm set to. Check that tool's settings in the database as well to make sure it's right. Post the two codes...
  11. Replies
    1
    Views
    570

    Ah, an old BotRods controller! Close to 20 years...

    Ah, an old BotRods controller! Close to 20 years old by now, perhaps. It should run up to SB3 v3.6.46, but since the SB 4g controller is basically a clone of it, it might be able to run a higher...
  12. Alt-1 to set the spindle on, bring up the keypad...

    Alt-1 to set the spindle on, bring up the keypad (spindle should start or at least the message to start it), use keyboard arrows to move or type in commands and enter. Alt-1 again to stop the...
  13. Oh my, I'm surprised that PC hasn't burnt up!!

    Oh my, I'm surprised that PC hasn't burnt up!!
  14. If you have a PRS or PRT Alpha, VN Switch #4 Stop...

    If you have a PRS or PRT Alpha, VN Switch #4 Stop Type should be Normally Closed. Is the physical E-Stop button reset (out), or pushed in? Rotate it to release it back to the out position. ...
  15. Thread: Odd noise

    by srwtlc
    Replies
    6
    Views
    999

    Good catch Russ! Yes, if the font wasn't created...

    Good catch Russ! Yes, if the font wasn't created in VCP, but brought in from another program as a dxf etc., you can get many nodes that then create "facets" for the letter or object profile, and that...
  16. Thread: Odd noise

    by srwtlc
    Replies
    6
    Views
    999

    If your cuts look good, it could just be that you...

    If your cuts look good, it could just be that you are using a feedrate that falls in a bad "motor resonance" range. Try some different feedrates to see if any sound better, and for best motion with...
  17. Replies
    13
    Views
    5,429

    One other thing to note, the "free" version of...

    One other thing to note, the "free" version of Fusion does not output rapid (jog) feedrates, just the cutting feedrates.
  18. Replies
    13
    Views
    5,429

    Greg is right, there are 3 post for SB there,...

    Greg is right, there are 3 post for SB there, just checked. I've never had need for machining a file from Fusion with my SB, but have posted a few for UCCNC and Centroid Acorn.
  19. Replies
    13
    Views
    5,429

    If you know JavaScript, you could edit or create...

    If you know JavaScript, you could edit or create one. You could try one of the basic G-code posts and see how it works (SB3 will run the basic G-code commands), but YMMV....greatly. SB HQ should...
  20. Replies
    3
    Views
    1,409

    Have you tried editing the file to set zero power...

    Have you tried editing the file to set zero power level after the spindle start, before the start of the first lase power motion? Could also try a different output for the laser that doesn't trigger...
  21. Thread: Past threads

    by srwtlc
    Replies
    1
    Views
    654

    Click on your user name and choose 'View Forum...

    Click on your user name and choose 'View Forum Posts', or click on advanced search in the upper right and do a search for all post with your user name.
    ...
  22. Replies
    3
    Views
    1,409

    Taylor, post the file, or at least the first part...

    Taylor, post the file, or at least the first part of it, so we can see what the code is doing. What program and post-processor are you using for generating the toolpath?
  23. Thread: Outer Profile

    by srwtlc
    Replies
    1
    Views
    602

    Check your chosen tool dimensions in Aspire's...

    Check your chosen tool dimensions in Aspire's tool database. Your part size is off by 0.25" each way. Bit diameter off by 0.125"? Or check the toolpath itself, do you have an offset applied?
  24. Replies
    7
    Views
    2,018

    Do you have a two head machine? Try changing the...

    Do you have a two head machine? Try changing the tool number to anything from 1-19.
  25. Replies
    7
    Views
    2,018

    Wrong Post chosen, possibly a non-spindle control...

    Wrong Post chosen, possibly a non-spindle control one. Open the part file in an editor and check for the spindle on code as well as an RPM value. New tool config possibly set at 0 RPM.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4