Search:

Type: Posts; User: tlempicke

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: FABMO Status

    by tlempicke
    Replies
    5
    Views
    274

    Gerald My first shopbot was in the 1990's and I...

    Gerald
    My first shopbot was in the 1990's and I am now on my fourth. I decided last Fall to upgrade the electronics. I am just ready to make chips and it appears that this is going to be a great...
  2. Replies
    3
    Views
    241

    Forgot we had that. Thanks

    Forgot we had that. Thanks
  3. Replies
    0
    Views
    112

    Spindle controller for Yaskawa drive

    This is a spindle controller that was purchased from Shopbot and is functionally identical to the newer one on sale for $250. Come with wiring harness and cable to connect to your computer.
    ...
  4. Replies
    3
    Views
    241

    Bump this message

    Bump this message
  5. Replies
    3
    Views
    241

    Spindle controller for Yaskawa V1000

    This is a spindle controller that was purchased from Shopbot and is functionally identical to the newer one on sale for $250. Come with wiring harness and cable to connect to your computer.

    $125...
  6. Replies
    1
    Views
    253

    Any interest at all out there?

    Any interest at all out there?
  7. Replies
    4
    Views
    340

    Shopbot can freely give their software away...

    Shopbot can freely give their software away because it is written to work with the Shopbot control board. So No.
  8. Replies
    1
    Views
    253

    SB motors for sale - from 48" Buddy

    I have three Shopbot motors for sale. These are from a 2008 Buddy and have seen only hobby use. All in perfect working condition. $150 each plus shipping....
  9. The box is sold

    The box is sold
  10. My email is tom@lempicke.com

    My email is
    tom@lempicke.com
  11. Replies
    5
    Views
    597

    Shopbot has them for sale at their site and also...

    Shopbot has them for sale at their site and also has the softwear for download. It is a really nice thing to have. As the computer starts up it is logged in as if it was a second keyboard. There...
  12. Shopbot Control box 4th gen for sale complete

    This is a Gen 4 control box that I have been using for the past few years. It is quite reliable and never has had many of the USB problems that you see here on the web. It is complete with three...
  13. Replies
    5
    Views
    597

    Shopbot Pendant

    Here is a picture of the pendant
  14. Replies
    5
    Views
    597

    Shopbot pendant FS

    I have a Shopbot USB pendant for sale. Excellent condition works perfectly.
    $75 includes shipping in the US.
  15. Replies
    8
    Views
    843

    It is probably a DC fan and so the extra wire is...

    It is probably a DC fan and so the extra wire is most likely a ground wire. Use an ohm meter and you can probably figure out what is what pretty quick. The pos and neg will have a resistance as...
  16. Replies
    0
    Views
    236

    Desktop software problems

    On Tuesday I used the machine and everything operated properly. I used a C3 command to home the machine about three times and each time it worked as it should. On Wednesday I turned the machine on...
  17. Replies
    54
    Views
    16,149

    "Elephant ears"

    Sorry to take so long getting these to you. Here are four pix. The first shows the "elephant ears" in action, the fourth shows the magnets that hold them to the supports for the...
  18. Replies
    9
    Views
    1,709

    Aspire embeds the codes in the shopbot cut file,...

    Aspire embeds the codes in the shopbot cut file, and if you have one of the larger VFD's it will use that to set the speed.

    For instance, say you have two bits in your tool file, both the same...
  19. Replies
    14
    Views
    3,563

    You will need a connection to the VFD to turn the...

    You will need a connection to the VFD to turn the spindle on and off. If I remember properly it will be just a set of dry pints on a relay. When they make contact the spindle runs and when they are...
  20. Thread: Rack Scraper

    by tlempicke
    Replies
    9
    Views
    808

    How about sending your E Mail so that I can Pay...

    How about sending your E Mail so that I can Pay Pal the bux to you?
    tom@lempicke.com
  21. Replies
    13
    Views
    1,352

    USB hub

    At one time Shopbot was giving out little guys that look like the pix attached. What it was all about was that the USB 2.0 standard was what the input board needed to see. By putting this hub into...
  22. Replies
    13
    Views
    1,352

    Yeah I have had the same problem. Easy to check...

    Yeah I have had the same problem. Easy to check with voltmeter.
  23. Replies
    13
    Views
    1,352

    "Spits the dummy" What on earth does that...

    "Spits the dummy"

    What on earth does that mean?

    Ahhhhh now I see -- that must be an Aussie expletive!

    Inside of your control box will be a small daughter board that is connected to the main...
  24. Shopbot is a valuable resource for support. They...

    Shopbot is a valuable resource for support. They can provide parts and information for whatever you need, and they will.
    Check with them to see if you are eligible to upgrade that software. ...
  25. Replies
    54
    Views
    16,149

    I have the same desktop and have dealt with a...

    I have the same desktop and have dealt with a similar problem. If the machine is making a "groaning" noise when the Y axis moves you have fouled the linear bearings on the left and right side of the...
Results 1 to 25 of 466
Page 1 of 19 1 2 3 4